Abstract:Wire arc additive manufacturing (WAAM) is a direct energy deposition process majorly used to fabricate large and medium-sized components. However, the process encounters defects, such as anisotropic microstructure and mechanical properties, residual stresses, excessive oxidation , and geometrical irregularities. Hence, efforts have been made to address the issues by optimizing the process parameters and incorporating in situ and post-process treatment to improve mechanical properties. In line with this, the present work deals with statistical-based process parameter optimization based on a multicriteria approach. The responses were quantified, statistically analyzed, and correlated with the process parameters. Travel speed exhibited a minor effect on all responses, while the current and wire feed speed significantly affected the responses. The percentage porosity was more sensitive to welding current than the other parameters. The maximum ultimate tensile strength (UTS) of 193.73 ± 3.93 MPa and yield strength (YS) of 108.09 ± 12.28 were displayed by Wall 2. YS and UTS showed marginal variation in vertical and horizontal directions, while % elongation showed significant variation. The desirability Wall (DW) exhibits better-forming quality due to the minimization of the contact angle, and fibrous silicon was observed between the layers. In contrast, it appears to be fragmented silicon at the interfacial region due to remelting and breakdown of Si. However, there were a few limitations to the DW wall's mechanical properties due to coarser dendrites and bulk eutectic at the interface. The average grain size of the bottom and top region for the optimized parameter is 111.156 μm and 173.66 μm, respectively. The observed texture components in the top region include C{001} 〈110〉, A2* (111) [11 2 ̄ ], A (1 1 ̄ 1) [110], and B (1 1 ̄ 2) [110], exhibiting a maximum texture intensity of 10.414. In the bottom region, the identified texture components are B ̄ ( 1 ̄ 1 2 ̄ ) [ 1 ̄1 ̄ 0], B (1 1 ̄ 2) [110], A (1 1 ̄ 1) [110], C{001} with a maximum texture intensity of 10.110.

Microstructure, Mechanical Properties and Tribological Behavior of Wire Electron Beam Additive Manufactured Eutectic Al–12Si Alloy

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples

Effect of Heat Treatment on the Evolution of Structural and Phase State in Wire Electron Beam Additively Manufactured Al–12Si Alloy

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Structure Formation and Mechanical Properties of Wire Arc Additively Manufactured Al4043 (AlSi5) Components

Wire Arc Additive Manufacturing with Novel Al-Mg-Si Filler Wire—Assessment of Weld Quality and Mechanical Properties

Influence of Microstructural Characteristics on the Mechanical and Wear Behavior of Wire Arc Additive Manufactured and Cast Eutectic Al-Si Alloy

The heterogeneous band microstructure and mechanical performance in a wire + arc additively manufactured 2219 Al alloy

Printing High-Strength High-Elongation Al4043 Alloy Using UNS A94043 Welding Wires through Wire Arc Additive Manufacturing

Microstructure and mechanical properties of wire arc additive manufactured ZL205A alloy

Deciphering the Microstructural Development and Excellent Ductility in Electron Beam Wire-Fed Additive Manufacturing of Ti-6Al-3Nb-2Zr-1Mo Alloys Based on High Deposition Rate

Microstructure Evolution of Wire-Arc Additively Manufactured 2319 Aluminum Alloy with Interlayer Hammering

Microstructural and mechanical properties of wire-arc additively manufactured Al–Zn–Mg aluminum alloy: The comparison of as-deposited and heat-treated samples

Investigating the microstructure and mechanical behavior of optimized eutectic Al Si alloy developed by direct energy deposition

Wire Arc Additive Manufacturing of Al-Cu Alloy-Grain Refinement, Strengthening and Thermal Simulation

Microstructure and properties research of Al-Zn-Mg-Cu alloy with high strength and high elongation fabricated by wire arc additive manufacturing

Tensile, Fatigue Properties and Their Anisotropies of Al-Mg Alloy Fabricated by Wire-Arc Additive Manufacturing

Microstructural evolution and mechanical characterization of wire arc additively manufactured 2Cr13 thin-wall part

Microstructure evolution and mechanical properties of wire-arc-additively manufactured Al–Cu–Mg–Ag alloy

Effects of solution temperature on microstructure and mechanical properties of Al-Si-Mg aluminum alloy fabricated by wire-arc additive manufacturing