Abstract:In the current paper, the correlation between the physical size of additively built wire arc specimens and their structure and properties is studied. For the purpose of this work, two oval shaped specimens of different lengths were manufactured under the same technological conditions. The specimens have a length of 200 mm and 400 mm and will be referred to as L200 and L400. The microstructure of the samples was studied using X-ray diffraction analysis (XRD), optical microscopy, and scanning electron microscopy (SEM). The microhardness, yield strength (YS), and ultimate tensile strength (UTS) were determined and their correlation with the technological conditions of specimen build-up was clarified. The results of the carried out experiments indicated that the crystallographic structure of both specimens is similar. The scanning electron microscopy images show a higher concentration of irregularly shaped micro-pores formed near the edge of the αAl grains in the structure of the L400 specimen compared to the L200 one. An increase in the size of the αAl solid solution grains in the case of the L200 specimen towards its top section was noticed using optical microscopy. A slightly lower magnitude change was noticed concerning the L400 specimen. The increase in the size of the aluminum crystals was determined to be the increasing interpass temperature. Due to the much smaller thermal dissipation capacity of the smaller specimen, the interpass temperature of the same increased faster compared to the larger specimen. All of the above-mentioned factors led to a decrease in the microhardness of the specimens at higher stages of build-up. Since the specimens were deposited using similar layer deposition conditions, the resultant YS and UTS data are also highly comparable.

Influence of Arc Length Correction on Friction and Wear Characteristics of Wire-Arc Additive Manufactured AA 5356 Alloy

Influence of Arc Length Correction on Microstructure, Mechanical Properties, and Defect Formation of Wire-Arc Additive Manufactured 5356 Alloy

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Influence of Microstructural Characteristics on the Mechanical and Wear Behavior of Wire Arc Additive Manufactured and Cast Eutectic Al-Si Alloy

Surface Characteristics, Microstructural, and Tribological Behavior of Wire Arc Additive Manufactured Aluminum-5356 Alloy

Wear Behavior Assessment of New Wire-Arc Additively Manufactured Surfaces on AA6061 and AA5086 Alloys through Multi-Walled Carbon Nanotubes and Ni Particles Inducement

Tribological performance of additive-manufactured aluminum alloy—effect of post-weld cold deformation

Microstructure, Hardness, and Electrical Resistivity of Al-Cu alloy fabricated via Wire Arc Additive Manufacturing

Understanding the microstructural evolution and fatigue behavior of aluminum 2319 fabricated by wire arc additive manufacturing

Microstructural Evolution and Mechanical Properties of 2219 Aluminum Alloy Deposited by Wire and Arc Additive Manufacturing

The heterogeneous band microstructure and mechanical performance in a wire + arc additively manufactured 2219 Al alloy

Investigating the Impact of Robotic Milling Parameters on the Surface Roughness of Al-Alloy Fabricated by Wire Arc Additive Manufacturing

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples

Influence of Heat Flow on the Grain Morphology and Porosity of Wire Arc Additive Manufactured 2319 Aluminum Alloy

Structure Formation and Mechanical Properties of Wire Arc Additively Manufactured Al4043 (AlSi5) Components

Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy

Enhancing the single-track deposition quality of AISI 308L wire arc additive manufacturing via process optimization and cold forging treatment

Dry Sliding and Slurry Abrasion Behaviour of Wire Arc Additive Manufacturing - Cold Metal Transfer (WAAM-CMT) Cladded Inconel 625 on EN8 Steel

Effect of Heat Treatment on Wire + Arc Additive Manufactured Aluminum 5356 Alloy: Mechanical Properties and Microstructure Correlation

Characterization of Al-Co-Cr-Fe-Mn-Ni High-Entropy Alloy Coating Fabricated onto AA5083 Using Wire-Arc Additive Manufacturing

Microstructure refinement and mechanical properties enhancement of wire-arc additive manufactured 2219 aluminum alloy assisted by interlayer friction stir processing