Abstract:The most important advantage of additive manufacturing by laser powder bed fusion (PBF-LB) technique is the ability to produce geometrically complex parts, but the problem is their rough surfaces, often difficult or inaccessible to finish by machining. Therefore, research to improve the reproducibility of the mechanical behavior of parts manufactured from aluminum alloy powders with as-built surfaces is of vital importance for the aerospace and automotive industries. Since local notches occurring on rough surfaces after the PBF-LB process are unavoidable, the way to solve this problem is to obtain as-built surfaces of the highest possible quality and to adapt a post-process heat treatment that increases the ductility and fracture toughness of the material. To this end, the present work focused on the study of the mechanical performance of AlSi7Mg0.6 samples with a rough as-built surface in the as-built state and after several variants of post-process heat treatment, combined with a detailed analysis of the microstructures corresponding to these states. Tensile samples built on a platform preheated to 100 °C, achieved a relative density of 99.85%, satisfactory surface quality, a relatively low level of residual stress and moderate crystallographic texture. Despite the rough surface, the samples under the as-built condition and after different variants of heat treatment (direct aging (DA), stress relieving (SR), and solution annealing followed by artificial aging (T6)), achieved tensile properties comparable to those reported in the literature for PBF-LB samples with machined surfaces. The resulting combinations of tensile properties of PBF-LB samples after different heat treatment variants were evaluated using the quality index (QI) commonly used to assess the quality of heat-treated Al-Si-Mg castings. It was found that the proposed T6 treatment provides the best combination of strength properties and ductility, compared to those obtained after both DA and SR, as well as after T6 treatment of high-quality castings, from the point of view of reducing the sensitivity of AlSi7Mg0.6 alloy to surface roughness.

Effect of build direction and surface finish on wear behavior of AlSi10Mg alloy casted by laser powder bed fusion

Effect of Build Orientation and Heat Treatment on Erosion Behavior of Al10SiMg Fabricated Using Laser Powder Bed Fusion

Wear Behavior of AlSi10Mg Alloy Produced by Laser‐Based Powder Bed Fusion and Gravity Casting

Comparative tribological studies of additive manufactured as-built and chemically polished AlSi10Mg alloy surfaces

The effect of abrasive water jet peening and laser shock peening on the wear properties of direct metal laser sintered AlSi10Mg alloy

Effect of α-Al and Si Precipitates on Microstructural Evaluation and Corrosion Behavior of Laser Powder Bed Fusion Printed AlSi10Mg Plates in Seawater Environment

Influence of eutectic-Si in as-cast and fibrous-eutectic-Si in LPBF-processed AlSi10Mg alloys on wear and corrosion behaviors treated with direct aging route

An Experimental Investigation into the Dry Reciprocating Wear Behavior of Additively Manufactured AlSi10Mg Alloys

Influence of Friction Stir Additive Manufacturing Parameters on Dry Friction and Wear Properties of Al-Mg-Si Alloy's Built Surfaces Fabricated by Sheet Lamination

Experimental Study on Circular Overhang Circularity and Surface Quality in AlSi10Mg Manufactured by Laser Powder Bed Fusion

Laser powder bed fusion processing of plasma atomized AlSi10Mg powder: Surface roughness and mechanical properties modification

Influence of Contour Scan Variation on Surface, Bulk and Mechanical Properties of LPBF-Processed AlSi7Mg0.6

Superior wear resistance in cast aluminum alloy via femtosecond laser induced periodic surface structures and surface hardening layer

Influence of Abrasive Materials in Fluidised Bed Machining of AlSi10Mg Parts Made through Selective Laser Melting Technology

Microstructure-induced anisotropic tribological properties of Sc-Zr modified Al–Mg alloy (Scalmalloy®) produced via laser powder bed fusion process

Effects of Building Direction, Process Parameters and Border Scanning on the Mechanical Properties of Laser Powder Bed Fusion AlSi10Mg

Comparative analysis on high temperature tribological behaviour of additive manufactured and cast AlSi10Mg alloy

An experimental investigation of the influence of SLM input factors on the as-built AlSi10Mg surface quality

Surface condition driven fatigue performance of laser powder bed fusion H13 steel

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Effect of Cross-Rolling on the Hardness of the AlSi10Mg Alloy Fabricated through Powder Bed Fusion