Abstract:The present investigation highlights the development of high-performance materials in the construction materials industry, with a special focus on the production of aluminium matrix composites (AMCs) containing titanium carbide (TiC) particles. The stir casting method with ultrasonic assistance was employed to enhance the mechanical and tribological properties. ASTM standards were employed to evaluate the influence of TiC particles on density, hardness (VHN), ultimate tensile strength (UTS), and wear resistance at various TiC weight fraction percentages (0.0 wt.%, 2.0 wt.%, 4.0 wt.%, 6.0 wt.%, and 8.0 wt.%). Field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) analysis were performed to analyse the microstructural changes and elemental phases present in the synthesised composite. Results revealed that the incorporation of 8 wt.% TiC reinforcement in the metal matrix composites demonstrated significant improvements compared to the base alloy. In particular, a substantial enhancement in hardness by 32%, a notable increase of 68% in UTS, and a significant 80% rise in yield strength were observed when contrasted with the pure aluminium alloy. The tensile fracture analysis of the specimens revealed the presence of dimples, voids, and cracks, suggesting a brittle nature. To assess the wear characteristics of the composites, dry sliding wear experiments were performed using a pin-on-disc wear tester. Incorporation of TiC particles resulted in a lower coefficient of friction than the base alloy, with the lowest friction coefficient being recorded at 0.266 for 6 wt.% TiC, according to the data. FESEM and energy-dispersive X-ray spectroscopy (EDXS) were used to examine the surfaces of the worn pin. Overall, the inclusion of TiC reinforcement particles in the matrix alloy greatly enhanced the wear resistance and friction coefficient of the Al-6TiC composites. Ploughing and adhesion under lower loads and delamination under higher loads were the wear mechanisms observed in the wear test.

Development, Testing and Characterization of Al NanoTiCp Composites through Powder Metallurgy Techniques

Effect of Secondary Processing and Nanoscale Reinforcement on the Mechanical Properties of Al-TiC Composites

Influence of TiC Particles on Mechanical and Tribological Characteristics of Advanced Aluminium Matrix Composites Fabricated through Ultrasonic-Assisted Stir Casting

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Preparation and Characterization of Hybrid Aluminum Matrix Composites Reinforced with MWCNT Using Powder Metallurgy Process

Preparation of ti-al based nanophase composite powder by mechanical alloying

Interfacial/intragranular reinforcement of titanium-matrix composites produced by a novel process involving core-shell structured powder

Effect of Nano-Silica Volume Reinforcement on the Microstructure, Mechanical, Phase Distribution and Electrochemical Behavior of Pre-Alloyed Titanium-Nickel (Ti-Ni) Powder

Investigation of mechanical and tribological behavior of Al-Ni-Co-MWCNT composites prepared by powder metallurgy technique

Thermal Analysis of Ni-Cu Alloy Nanocomposites Processed by Sand Mold Casting

Nanocrystalline NiTiB reinforced aluminum matrix composites: Synthesis, structural, mechanical and corrosion properties

Development of Al-Ni-TiC Composite Coating on Commercially Pure Al Using Tungsten Inert Gas Welding Route and its Wear Behavior

Characterization and Investigation of Mechanical Properties of Aluminium Hybrid Nano-composites: Novel Approach of Utilizing Silicon Carbide and Waste Particles to Reduce Cost of Material

Preparation of in situ TiC@TiN core–shell and Ti2N–Al4C3 nanoparticles and their effects on Al–Zn–Mg–Cu alloy

Synthesis and Characterization of Recycled-TiC Reinforced AlZnMgCu Powder Metallurgy Composites

Nanoindentation and isothermal compression behaviour of Al–4Cu–Ni composites

Effect of Increasing the Strength of Aluminum Matrix Nanocomposites Reinforced with Microadditions of Multiwalled Carbon Nanotubes Coated with TiC Nanoparticles

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

Tribological, mechanical and microstructure characteristics of hybrid aluminium matrix composite containing titanium carbide (TiC) and graphite particles

Fabrication of Nano-Ticp Reinforced Inconel 625 Composite Coatings by Partial Dissolution of Micro-Ticp Through Laser Cladding Energy Input Control

Micro/Nanostructure and Tribological Characteristics of Pressureless Sintered Carbon Nanotubes Reinforced Aluminium Matrix Composites