Abstract:Over the last few decades, "Discontinuously Reinforced Particulate Composites (DRPCs)" are a popular class of composite materials with considerable challenge in processing, characterization and machinability because of their increased strength-weight ratio, stiffness, specific strength and oxidization when compared to various metals and their alloys. This paper discusses experimental and numerical investigation on mechanical characteristics of aluminum metal matrix reinforced with various reinforcement particulates such as silicon carbide, aluminium oxide, and zirconium oxide, compaction pressure (kN) and hold time (s) based on Design of Experiments (DOE) and Finite Element Analysis. Initially this paper discusses the process optimization of Aluminum Matrix reinforced with different particulates experimentally to identify the favourable processing conditions by varying reinforcement materials, compaction pressure (kN) and hold time (s) based on TDOE (Taguchi's Design of Experiments). Further, this paper concentrates to determine "maximum principal stress, equivalent elastic strain and equivalent (von-mises) stress" based on Finite Element Analysis (ANSYS Workbench-2023R1). The results of the experimentation showed that the highest hardness values were achieved with ZrO2 reinforcement material. Increasing the compaction pressure from 8 to 12 kN resulted in a slight decrease in surface roughness and porosity. Higher compaction pressures have assumed to facilitate better particle distribution and improved interfacial bonding, leading to smoother surfaces and lower void content. The simulation results showed that the maximum principal stress achieved were (2235.8 Mpa) SiC, (3444.4 Mpa) Al2O3, and (3582.5 MPa) ZrO2. The equivalent elastic strain achieved was (0.2488) SiC, (0.2421) Al2O3 and (0.262) ZrO2. The equivalent (Von Mises) stress achieved was (28751 MPa) for SiC, (24880 MPa) for ZrO2 and (26972 Mpa) for Al2O3. This experimentation and simulation demonstrated that the PM process can be used to fabricate DRAMMC with different reinforcement particulates.

Characterization and Investigation of Mechanical Properties of Aluminium Hybrid Nano-composites: Novel Approach of Utilizing Silicon Carbide and Waste Particles to Reduce Cost of Material

Experimental Investigation and Comparative Analysis of Aluminium Hybrid Metal Matrix Composites Reinforced with Silicon Nitride, Eggshell and Magnesium

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Investigation on Mechanical Behavior of Al6061- Coconut Shell Ash- Granite Dust Reinforced Hybrid Metal Matrix Composites Manufactured using Stir Casting Technique

Experimental Investigation on Metal Matrix Nanocomposite: Aluminium Alloy 6061 and 7075 with SiC and Fly Ash

Investigation of Mechanical Properties of Aluminium 6061-Silicon Carbide, Boron Carbide Metal Matrix Composite

Investigation of Stress and Wear Analysis for Aluminum-based Metal Matrix Composite Reinforced Silicon Carbide using ANSYS Software Package

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Fabrication and Mechanical Behaviour Investigation on Aluminium 7075 Boron Carbide and Inconel Alloy 625 Metal Matrix Composite Using Ultra Sonic Stir Casting Method

Morphological and mechanical behavior of novel Al7075 (T6) + 3.5% SiC + 0.3% CR + 5.5% MoS2-based green hybrid composite: An experimental analysis and optimization via TOPSIS

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Experimental investigation of material properties of Al-Sic-fly ash composite

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

An integrated experimental and analytical approach on mechanical characterization of advanced powder metallurgy aluminium metal matrix composites reinforced with different particulates

Investigation on Mechanical Properties of Agro and Industrial Waste Reinforcement in Aluminium 7075 Composite with Liquid Metal Stir Casting Route

Mechanical Behaviour of Aluminium Hybrid Composites Reinforced with: Rice Husk Ash - Silicon Carbide - Copper Nanoparticles

Influence of hybrid nanoparticles on the wear behavior of aluminum alloy composites for aerospace applications

Development of high-performance aluminium 6061/SiC nanocomposites by ultrasonic aided rheo-squeeze casting method

Microstructural Characterization, Mechanical And Wear Behaviour Of Al2024-B4C Composites For Aerospace Applications