Abstract:This study aims to examine the impact of agricultural waste materials—specifically silicon carbide (SiC) and palm sprout shell ash (PSSA)—on the mechanical properties, including density, porosity, tensile strength, compression strength, flexural strength, impact strength, and hardness, as well as the tribological behavior of Al-Cu-Mg alloy-based HRAMMCs. Parametric optimization was conducted on HRAMMCs to predict the effect of input constraints on the performance of the composite, considering the weight percentage of SiC, PSSA, and ultrasonic-assisted stirring time. Taguchi's L9 orthogonal array was used for the design of experiments (DOE), and the composites were fabricated accordingly. Their physical, mechanical, and tribological properties were determined experimentally. Taguchi-based Grey Relational Analysis for multi-optimization highlighted the potential of the HRAMMCs, with a density of 2.545 g/cm3, porosity of 5.810%, ultimate tensile strength of 341 MPa, flexural strength of 321 MPa, compressive strength of 394.016 MPa, Vickers hardness of 136.883 HV, wear rate of 6.88E-12 m3/m, and a coefficient of friction of 0.397. ANOVA shows that the developed mathematical model is a better fit for examining the impact of various factors on the GRG of and corresponding properties of developed HRAMMCs, Indicating the R2 value of the developed model is 99.33% (0.9933). The 2 wt.% SiC, 2 wt.% PSSA, and a stirring time of 7 minutes are optimal parameters for the present HRAMMCS; to reduce porosity, wear loss, and the coefficient of friction while increasing flexural strength, ultimate tensile strength, compressive strength, and Vickers microhardness. Moreover, the examination of the tensile and impact fracture surfaces and worn surfaces was carried out using SEM analysis of the alloy and composite produced under the optimal experimental conditions. The results of the fracture surface analysis indicated that the failure of both tensile and impact fractures was due to a amalgamation of ductile and brittle behaviors. The composites exhibited lower ductility than that of the base alloys. A study of the wear mechanism revealed that it was a mixture of adhesive and abrasive wear mechanisms. The SiC and PSSA ceramic reinforcements demonstrate higher hardness compared to the alloy, which restricts the fluid-like movement of the matrix. When these reinforcements were added to the alloy, they substantially decreased the occurrence of severe delamination and the formation of adhesive wear particles.

Morphological and mechanical behavior of novel Al7075 (T6) + 3.5% SiC + 0.3% CR + 5.5% MoS2-based green hybrid composite: An experimental analysis and optimization via TOPSIS

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Empirical investigation on controlled porosity level and dry sliding wear behavior of Al7075-(T6) doped with SiC+MoS2 based hybrid composites via advanced vacuum-assisted stir casting

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Morphological evolution and strength performance of green-aluminium-7075 hybrid composites modeled by response surface analysis

Experimental Investigation and Comparative Analysis of Aluminium Hybrid Metal Matrix Composites Reinforced with Silicon Nitride, Eggshell and Magnesium

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

Mechanical and wear analysis of AA6061-T6-SiC-TiC-graphite metal matrix composite

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Investigation on Mechanical Behavior of Al6061- Coconut Shell Ash- Granite Dust Reinforced Hybrid Metal Matrix Composites Manufactured using Stir Casting Technique

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

SiC and MWCNT Blending Actions on Functional Performance of Hybrid AA2024 Alloy Nanocomposite Via Two Step Stir Cast Route

Performance analysis and mechanical behavior of aluminum metal matrix composite

Characterization and Investigation of Mechanical Properties of Aluminium Hybrid Nano-composites: Novel Approach of Utilizing Silicon Carbide and Waste Particles to Reduce Cost of Material

Mechanical and Sliding Wear Performance of AA356-Al2O3/SiC/Graphite Alloy Composite Materials: Parametric and Ranking Optimization Using Taguchi DOE and Hybrid AHP-GRA Method

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Taguchi-based Grey Relational Analysis for multi-response optimization of the characteristics of HRAMMCs reinforced with agro-waste and SIC produced by ultrasonic-assisted bottom pour two-stage stir casting

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Development & Fabrication of AL-3Mg Based SiC & Gr. Hybrid Metal Matrix Composite by Stir Casting Method

Green metal matrix composites: a multi-faceted study on Al alloy composites with egg shell powder and silicon carbide as reinforcements

Hybrid Filler Actions on Functional Performance Evaluation of Magnesium Alloy (AZ61) Hybrid Nanocomposites