Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Investigation of mechanical and tribological behavior of Al-Ni-Co-MWCNT composites prepared by powder metallurgy technique

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

DRY AND HOT CORROSION BEHAVIOUR OF Al-Ni-Co-x MWCNT COMPOSITES PROCESSED THROUGH POWDER METALLURGY

Micro/Nanostructure and Tribological Characteristics of Pressureless Sintered Carbon Nanotubes Reinforced Aluminium Matrix Composites

Microstructure and Mechanical Properties of ABOw and Nickel-Coated MWCNTs Reinforced 2024al Hybrid Composite Fabricated by Squeeze Casting

Investigating phase and magnetic properties in Co-2 wt.% MWCNT nano-composites prepared by mechanical alloying

Fabrication and Tribological Properties of Carbon Nanotubes-Aluminum Composites

Investigation on the mechanical and tribological behavior of tungsten-reinforced Ti-5Al-2.5Sn composites

Influence of Molybdenum Content and Load on the Tribological Behaviors of In-Situ Cr3C2-20 Wt % Ni Composites

Preparation and Characterization of Hybrid Aluminum Matrix Composites Reinforced with MWCNT Using Powder Metallurgy Process

Tribological Behavior of Powder Metallurgy Processed Carbon Nanotube Reinforced Alsi Functionally Graded Materials

Fabrication and tribological properties of carbon nanotubes reinforced Al composites prepared by pressureless infiltration technique

Investigations on microstructural, mechanical, and tribological properties of Al-Cu-Ni alloy in cast, heat-treated, and strain-softened conditions

Mechanical Effects of Carbon Nanotubes-Graphene Reinforced Aluminium Matrix Composites

Microstructure, Mechanical Properties and High Temperature Tribological Behavior of NiAl-based Composites

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite

Electrochemical deposition and tribological behaviour of Ni and Ni–Co metal matrix composites with SiC nano-particles

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

The Influence of the Modification of Carbon Nanotubes on the Properties of Copper Matrix Sintered Materials

Carbon Nanotubes Improves the Tribological Properties of Ni60/Al<sub>2</sub>O<sub>3</sub> Coatings

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating