Abstract:Objective To evaluate the effect of SiO2-ZrO2 slurry coating on surface performance of zirconia ceramic.Methods Seventy pre-sintered zirconia discs were randomly divided into seven groups with 10 discs per group.Sample discs in each group received one of the following seven different surface treatments, namely, sintered(group AS), sand blasting after sintered(group SB), coated with slurry of mole ratio of SiO2 to ZrO2 2: 1(group 2SiO2-1ZrO2), coated with slurry of mole ratio of SiO2 to ZrO2 1: 1(group 1SiO2-1ZrO2), coated with slurry of mole ratio of SiO2 to ZrO2 1 : 2(group 1SiO2-2ZrO2), coated with slurry of mole ratio of SiO2 to ZrO2 1 : 3(group 1SiO2-3ZrO2), coated with slurry of mole ratio of SiO2 to ZrO2 1:4(group 1 SiO2-4ZrO2).Profilometer, X-ray diffractometer(XRD), energy dispersive spectrometer, scanning electron microscopy(SEM) were used to analyze surface performance.Results The surface roughness of the discs in group AS was lower than those in the other groups[(0.33 ± 0.03) μm] (P＜0.05), there was no statistically significant difference(P＞0.05) among group 2SiO2-1ZrO2[(3.85±0.38) μm], group 1SiO2-1ZrO2[(3.78±0.56) μm] and group 1SiO2-2ZrO2[(4.06 ± 0.48) μtm], and no difference(P＞0.05) was observed between group 1SiO2-3ZrO2 [(1.02±0.09) μm] and group 1SiO2-4ZrO2[(1.53±0.23) μm] either.However, surface roughness in all coating groups was higher than those in group SB[(0.86 ± 0.05) μm] (P＜0.05).According to the XRD pattern, group AS and all coating groups consisted of 100％ tetragonal airconia and monoclinic zirconia was detected at surface of group SB.Contents of surface silicon of coating groups increased significantly,however, no silicon was detected at sample surface of group AS and group SB.SEM showed that zirconia grains of coating exposed since part of silicon was etched by hydrofluoric acid, a three-dimensional network of intergrain nano-spaces was created.Conclusions SiO2-ZrO2 slurry coating could make surface of zirconia rough and increase Si content without creating monoclinic zirconia.

Preparation of the rod-shaped SiO2@C abrasive and effects of its microstructure on the polishing of zirconia ceramics

Preparation of the Nanodiamond@SiO2 Abrasive and its Effect on the Polishing Performance of Zirconia Ceramics

Trivalent lanthanum and ytterbium doped meso-silica/ceria abrasive systems toward chemical mechanical polishing (CMP) and ultraviolet irradiation-assisted photochemical mechanical polishing (PCMP)

Surface Planarization of Zirconia Ceramic Achieved by Polyacrylamide Grafted Nanodiamond Composite Abrasives Through Chemical Mechanical Polishing

Nano-scale surface of ZrO2 ceramics achieved efficiently by peanut-shaped and heart-shaped SiO2 abrasives through chemical mechanical polishing

Non-spherical abrasives with ordered mesoporous structures for chemical mechanical polishing

Photocatalysis-Assisted Chemical Mechanical Polishing of SiC Wafer Using a Novel SiO2@TiO2 Core-Shell Composite Nanoparticles Slurry

Effect of SiO2-ZrO2 slurry coating on surface performance of zirconia ceramic

Preparation of porous alumina/ceria composite abrasive and its chemical mechanical polishing behavior

Influence of Cerium Oxide Abrasive Particle Morphologies on Polishing Performance

Investigation on Polishing of Zirconia Ceramics Using Magnetic Compound Fluid: Relationship Between Material Removal and Surface Roughness

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

A special electrostatic self-assembly structure of colloidal silica: Improving Chemical Mechanical Polishing performance

Preparation of Flower-Shaped Silica Abrasives by Double System Template Method and Its Effect on Polishing Performance of Sapphire Wafers

Synthesis, Characterization of Ceo2@Zif-8 Composite Abrasives and Their Chemical Mechanical Polishing Behavior on Glass Substrate

An experimental investigation of scan trajectory into the underwater femtosecond laser polishing SiC ceramic

Polishing of Zirconia Ceramics by Chemically-Induced Micro-Nano Bubbles

Study on uniform size and spherical CeO 2 abrasives synthesized by two-step method and their chemical mechanical polishing performances

A novel optimized two-step method for preparing the Z-pin-like rods to improve their effect on the ablation resistance of C/C-ZrC-SiC

Preparation of Non-Spherical Silica Composite Abrasives by Lanthanum Ion-Induced Effect and Its Chemical–mechanical Polishing Properties on Sapphire Substrates

Photocatalytic assisted chemical mechanical polishing for silicon carbide using developed ceria coated diamond core-shell abrasives