Abstract:Although <math>{101¯2}</math> twinning behavior has been extensively studied, it has rarely been investigated under biaxial tension. In the present research, the mechanical response and <math>{101¯2}</math> twinning behavior of a Mg AZ31 sheet under biaxial tension with various stress ratios (<math>σND:σTD</math>) along the normal direction (ND) and transverse direction (TD) were systematically studied. The results indicate that the yield stress along the ND is nearly independent of <math>σND:σTD</math>. Schmid law applied to <math>{101¯2}</math> twinning under biaxial tension yields better efficiency than that for uniaxial tension, and a higher efficiency is observed with a larger stress ratio along the TD; the fraction of experimentally observed twin variants with Schmid factors (SFs) of ranks 1 and 2 is approximately 45% for uniaxial tension, whereas it is approximately 68% for <math>σND:σTD=2:1</math> and approximately 88% for <math>σND:σTD=1:2</math>. This result contradicts with the previously reported result that Schmid law is more efficient for uniaxial stress states than under multiaxial stress conditions. It is found that biaxial tension will increase the difference in SF for the six twin variants and make Schmid law more efficient. Twin variant selection and volume fraction are highly dependent on <math>σND:σTD</math>. For uniaxial tension, the activities for the six variants are similar, and the (0002) poles of the twins are distributed evenly on a circle approximately 80°–90° away from the ND. In contrast, the variants <math>(01¯12)[011¯1]</math> and <math>(011¯2)[01¯11]</math> are more favorable under biaxial tension, and more (0002) poles of the twins concentrate around the rolling direction with a higher ratio of <math>σTD</math>. At a similar strain level, the twin fraction under biaxial tension is often different from that under uniaxial tension, and this difference varies with <math>σND:σTD</math>. This mechanism is associated with a stress-ratio-mediated detwinning behavior under biaxial tension. The findings in the present study provide a new and significant understanding of the twinning behavior of Mg alloys.

The different effects of twin boundary and grain boundary on reducing tension-compression yield asymmetry of Mg alloys

Effect of Loading Direction on Tensile-Compressive Mechanical Behaviors of Mg-5Zn-2Gd-0.2Zr Alloy with Heterogeneous Grains

Effects of extrusion ratio and subsequent heat treatment on the tension-compression yield asymmetry of Mg-4.58Zn-2.6Gd-0.18Zr alloys

The Dislocation-Twin Interaction and Evolution of Twin Boundary in AZ31 Mg Alloy

Effects of initial grain size and orientation on the twin behavior in ZK60 Mg alloy

Effect of Local Stresses of Primary Twinning on Double Twinning, Twin Intersection and Their Competition

Influence of precipitation on tension and compression twinning in Mg-6.5Zn alloy

{ 10 1 ̄ 2 } twinning behavior under biaxial tension of Mg–3Al–1Zn plate

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

Tension—compression asymmetry and corresponding deformation mechanism in ZA21 magnesium bars with bimodal structure

Quantifying the effect of twin boundaries on grain boundary activities in nanotwinned copper: A molecular dynamics simulation

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

The effect of grain size on deformation modes and deformation heterogeneity in a rolled Mg-Zn-Ca alloy

Improvement of dynamic compression properties and strengthening mechanism of Mg–Y–Nd–Gd–Zr alloy by pre-twinning

The effects of orientation control via tension-compression on microstructural evolution and mechanical behavior of AZ31 Mg alloy sheet

Tailoring bimodal grain structure of Mg-9Al-1Zn alloy for strength-ductility synergy: Co-regulating effect from coarse Al2Y and submicron Mg17Al12 particles

Effects of {10-12} Twin Boundary on Nanotribological Behavior of Pure Mg: A Molecular Dynamics Simulation

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

A quantitative study on mechanical behavior of Mg alloys with bimodal texture components

Strengthening mechanisms of semi-coherent boundaries between Al8Mn4Y and the Mg matrix in magnesium alloys

The study of grain boundary density effect on multi-grain thin film under tension