Abstract:Highlights • Effects of microstructure inhomogeneity on tensile deformation behavior of ZK60 Mg were clarified. • Tensile temperature and loading direction determined the slipping- or twinning-dominated deformation mode. • DRX was changed from continuous mode to discontinuous mode with increasing tensile temperature. • Welding zone showed superplastic behavior at tensile temperature > 300 °C due to the GBS effects. • The texture evolution was dependent on loading direction, tensile temperature and recrystallization mode. The tensile tests of the extruded ZK60 Mg containing a longitudinal weld seam were carried out at room and elevated temperatures, and the effects of induced microstructure inhomogeneity on tensile deformation behavior was clarified. The results show that the deformation mode, dynamic recrystallization (DRX), texture evolution and mechanical properties are strongly affected by the longitudinal weld seam, temperature, and loading direction. The room temperature (RT) deformation of welding zone is controlled by the dislocation slips with the association of some twins, while twinning plays significant roles in the accommodation of c -axis strain of the coarse grains on matrix zone. The deformation at RT stretched along extrusion direction (ED) and transverse direction (TD) are controlled by basal slip/twinning and basal slip/prismatic slip/twinning, respectively. During high temperature tension, the dislocation cross slip of pyramidal slip is activated, and grain boundary sliding occurred in welding zone, leading to the superplastic behavior. With the increase of tensile temperature, the predominant DRX mode is transformed from continuous DRX to discontinuous DRX. Moreover, the basal poles of the grains spread from TD towards ED with the decrease of maximum pole intensity when stretched along ED, while non-basal textures are transformed to 〈10–10〉 fiber texture when stretched along TD. The slip-dominated flow is seen during RT tension along ED, while twinning becomes predominant during RT tension along TD. The fine grain structure causes the superior RT tensile properties along ED of welding zone with ultimate tensile strength of 315 MPa and elongation to failure of 13.8%. With the increase of tensile temperature, the slipping-dominated deformation is transformed into twinning-dominated, causing the decrease of strength and increase of elongation.

Effects of initial grain size and orientation on the twin behavior in ZK60 Mg alloy

The Effect of Grain Size on the Strain Hardening Behavior for Extruded ZK61 Magnesium Alloy

Twinning Behavior, Microstructure Evolution and Mechanical Property of Random-Orientated ZK60 Mg Alloy Compressed at Room Temperature

A comprehensive analysis on microstructure evolution of Mg-5.65Zn-0.66Zr alloy during hot deformation

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

Effect of Loading Direction on Tensile-Compressive Mechanical Behaviors of Mg-5Zn-2Gd-0.2Zr Alloy with Heterogeneous Grains

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure and mechanical properties of extrusion ZC61 alloys under different dynamic compression loading directions

Tensile Mechanical Properties and Deformation Mechanism of the Extruded ZM61 Magnesium Alloy at High Strain Rates

Effect of twinning on the deformation behavior of an extruded Mg-Zn-Zr alloy during hot compression testing

Effects of extrusion ratio and subsequent heat treatment on the tension-compression yield asymmetry of Mg-4.58Zn-2.6Gd-0.18Zr alloys

Investigation of the microstructure and properties of extrusion-shear deformed ZC61 magnesium alloy under high strain rate deformation

Compressive deformation behavior of ultrafine-grained Mg-3Zn-1.2Ca-0.6Zr alloy at room temperature

Effects of Zn content and initial grain size on double peak basal textures of Mg-Zn-Al alloys

Microstructure and mechanical properties with various pre-treatment and Zn content in Mg-Gd-Y-Zn alloys

Experimental study on tensile deformation behaviors under room and elevated temperatures induced by microstructure inhomogeneity of ZK60 Mg with a longitudinal weld

Effects of extrusion ratio and temperature on the microstructure and mechanical properties of Mg–Zn–Yb–Zr extrusion alloys

Hot compression behavior and microstructure evolution of Mg-Gd-Y-Zn-Zr alloy

Microstructure characteristics, yield asymmetry and fracture mechanism of the fine grained thin-wall Mg-6.03Zn-0.55Zr tubes fabricated by hot spinning

Influence of grain size on twinning behavior of WE43 magnesium alloy during room-temperature compression deformation

Effect of Zn/(Gd+Y) ratio on the microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy