Abstract:The effect of large pre-deformation on the microstructural evolution and mechanical property anisotropy of large-sized Al-Zn-Mg alloy extruded profiles with thin-walls and high-ribs was investigated. The increase in pre-deformation reduces the time required for the alloy to reach peak hardness during aging at 120 °C, but leads to a decrease in peak hardness. The undeformed alloy exhibits the highest ultimate tensile strength (UTS) of 527 MPa and yield strength (YS) of 497 MPa in the 90° direction, accompanied by a low elongation (EL) of 12.7 %, highlighting significant anisotropy. At a large pre-deformation of 38 %, UTS, YS, and EL dramatically fall, with IPA values of 2.43 %, 3.77 %, and 11.96 %, respectively. Increased pre-deformation promotes the formation of substructures without altering the texture type, which remains predominantly A 1 * and A 2 * textures, but reduces texture intensity. After aging treatment, the primary intragranular precipitates are η' phases, and dislocations generated by pre-deformation stimulate the heterogeneous nucleation of η' phases and their transformation to η phases. Additionally, increased pre-deformation leads to the growth and uneven distribution of precipitates and an increase in the width of the precipitate-free zones (PFZ). The reduced anisotropy is attributed to decreased texture intensity, increased dislocation substructures, higher η phase content, and expanded PFZ width. Pre-deformation between 8 % and 18 % effectively maintains mechanical properties while reducing anisotropy. These findings provide insights into optimizing pre-deformation treatments to balance mechanical properties and anisotropy in Al-Zn-Mg alloy profiles.

Effects of Zn content and initial grain size on double peak basal textures of Mg-Zn-Al alloys

Effect of Al Concentration on Basal Texture Formation Behavior of AZ-Series Magnesium Alloys during High-Temperature Deformation

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys

Effects of initial grain size and orientation on the twin behavior in ZK60 Mg alloy

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

Effects of extrusion ratio and subsequent heat treatment on the tension-compression yield asymmetry of Mg-4.58Zn-2.6Gd-0.18Zr alloys

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

Effects of deformation parameters on microstructure and texture of Mg–Zn–Ce alloy

A comprehensive analysis on microstructure evolution of Mg-5.65Zn-0.66Zr alloy during hot deformation

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Grain size dependence of annealing strengthening of an extruded Mg-Gd-Zn alloy subjected to pre-compression deformation

Effects of Zn Addition and Twin Roll Casting Process on the Microstructure, Texture, and Mechanical Properties of the Mg-Al-Mn-Ca Sheet

Effect of large pre-deformation on the microstructure, texture and mechanical properties of Al-Zn-Mg alloy extruded profiles

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Effect of Zn Content on the Microstructure and Mechanical Properties of Al-Mg-Zn-Sc Alloys with Friction Stir Processing and Post-Heat Treatment

Thermal Stability of Different Texture Components in Extruded Mg–3Al–1Zn Alloy

Effect of Zn/Mg Ratio on Microstructure and Properties of Cold Extruded Al-xZn-2.4Mg-0.84Cu-0.2Zr-0.25Ti Aluminum Alloy

Effect of transverse gradient extrusion process on texture and mechanical properties of Mg–3Al–1Zn alloy sheets