Abstract:For further efficiency improvement in kesterite-type Cu2ZnSn(S,Se)4 (CZTSSe) solar cells, it is essential to address the carrier recombination issue at the back electrode interface (BEI) caused by the undesirable built-in potential orientation toward an absorber as an n-MoSe2 interfacial layer formed. In this regard, back surface field (BSF) incorporation, i.e., field-effect passivation, shows promise for dealing with this issue due to its positive effect in decreasing recombination at the BEI. In this study, the BSF was realized with the p-type conduction transition in interfacial layer MoSe2 by incorporating Nb into the back electrode. The BSF width can be tuned via modulating the carrier concentration of the absorber, which has been demonstrated by capacitance–voltage characterization. A beyond 7% efficiency BSF-applied CZTSSe solar cell is prepared, and the effects of a tunable BSF and the mechanism underpinning device performance improvement have been investigated in detail. The wider BSF distribution in the absorber induces a decrease in reverse saturation current density (J0) due to the stronger BSF effect in suppressing BEI recombination. As a result, an accompanying increase in open-circuit voltage (VOC) and short-circuit current density (JSC) is achieved as compared to the BSF-free case. This study offers an alternative strategy to address the BEI recombination issue and also broadens the interface passivation research scope of potentially competitive kesterite solar cells.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c10561?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c10561</a>.EDS spectrum of a Mo:Nb film grown on the SLG substrate and statistical histograms of the absorber grain size distribution from the SEM images in <a class="internalNav" href="#fig5">Figure </a><a class="internalNav" href="#fig5">5</a>a,b; composition ratios in CZTS precursor solution; the compositions of MoSe2 and MoSe2:Nb films measured via EDS and XPS and those of CZTSSe films prepared on the SLG substrate measured by EDS (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c10561/suppl_file/am0c10561_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Facile Tailor on the Surface of Mo Foil Toward High‐Efficient Flexible CZTSSe Solar Cells

A quasi-ohmic back contact achieved by inserting single-crystal graphene in flexible Kesterite solar cells

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Interface optimization and defects suppression via NaF introduction enable efficient flexible Sb 2 Se 3 thin-film solar cells

Flexible Substrate‐Structured Sb2S3 Solar Cells with Back Interface Selenization

Back Contact Engineering to Improve CZTSSe Solar Cell Performance by Inserting MoO3 Sacrificial Nanolayers

Heterojunction interface regulation to realize high-performance flexible Kesterite solar cells

Modification of Back Contact in Cu 2 ZnSnS 4 Solar Cell by Inserting Al-Doped ZnO Intermediate Layer

Modulation of Field-Effect Passivation at the Back Electrode Interface Enabling Efficient Kesterite-Type Cu 2 ZnSn(S,Se) 4 Thin-Film Solar Cells

Effect of TiN diffusion barrier layer on residual stress and carrier transport in flexible CZTSSe solar cells

Antimony incorporated flexible Cu 2 ZnSn(S,Se) 4 solar cell for enhanced mechanical endurance and efficiency

Efficient and bending durable flexible perovskite solar cells via interface modification using a combination of thin MoS2 nanosheets and molecules binding to the perovskite

10.24% Efficiency of Flexible Cu2 ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

In-doping collaboratively controlling back interface and bulk defects to achieve efficient flexible CZTSSe solar cells

50-Μm Thick Flexible Dopant-Free Interdigitated-Back-contact Silicon Heterojunction Solar Cells with Front MoOx Coatings for Efficient Antireflection and Passivation.

Thermoplastic elastomer enhanced interface adhesion and bending durability for flexible organic solar cells

Back Contact Plasma Treatment Enables 14.5% Efficient Solution‐Processed CuIn(S,Se)2 Solar Cells

Interfacial Engineering to Improve Cu2ZnSnX4 (X = S, Se) Solar Cell Efficiency

Highly Efficient and Highly Flexible Thin Crystalline Silicon Heterojunction Solar Cells Based on Dopant-Free Carrier-Selective Contacts Fabricated with Simple Processes

Back contact modification of the optoelectronic device with transition metal dichalcogenide VSe2 film drives solar cell efficiency

11.88% Efficient Flexible Ag‐Free CZTSSe Solar Cell: Spontaneously Tailoring the Alkali Metal Level