Abstract:The addition of alkali elements has become mandatory for boosting solar cell performance in chalcogenide thin films based on kesterites (Cu2ZnSnS4, CZTS). A novel doping process is presented here, that consists in the incorporation of sodium or lithium during the deposition of the CdS buffer layer, followed by a Post-Deposition Annealing (PDA). As the doping route leads to more efficient devices in comparison with the undoped reference sample, the influence of PDA temperature was also investigated. Compositional profiling techniques (TOF-SIMS and GDOES) revealed a dependence of the alkaline distribution in kesterites with the PDA temperature. Although the doping process is effective in that it increases the alkaline concentration compared to the undoped sample, the compositional profiles indicate that a significant proportion of Li and Na remains "trapped" within the CdS layer. In the 200-300 oC range the alkali profiles registered the higher concentration inside the kesterite. Despite this, an additional alkali accumulation close to the Mo/FTO substrate was found for all the samples, which is frequently related to alkali segregation at interfaces. The addition of both, lithium and sodium, improves the photovoltaic response compared to the undoped reference device. This is mainly explained by a substantial improvement in the open-circuit potential (Voc) of the cells, with best devices achieving efficiencies of 4.5% and 3% for lithium and sodium, respectively. SEM images depicted a "bilayer structure" with larger grains at the top and small grains at the bottom in all samples. Moreover, the calculated bandgap energies of the CZTS films account for changes in the crystallographic order-disorder of the kesterites, more related to the PDA treatment rather than alkali incorporation. Even if further optimization of the absorber synthesis and doping process will be required, this investigation allowed the evaluation of a novel strategy for alkali incorporation in kesterite based solar cells.

11.88% Efficient Flexible Ag‐Free CZTSSe Solar Cell: Spontaneously Tailoring the Alkali Metal Level

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Heterojunction interface regulation to realize high-performance flexible Kesterite solar cells

Defect Engineering in Earth-Abundant Cu2ZnSnSe4 Absorber Using Efficient Alkali Doping for Flexible and Tandem Solar Cell Applications

Substitution of Ag for Cu in Cu2ZnSn(S,Se)4: Toward Wide Band Gap Absorbers with Low Antisite Defects for Thin Film Solar Cells

Passivation of Grain Boundaries and Defects in CZTSSe Solar Cells by In Situ Na Doping

Li, Ag Co‐Doping Enables Efficient Kesterite Solar Cell with a High Fill Factor of 74.30%

Structural, Electronic and Defect Properties of Cu 2 ZnSn(S,Se) 4 Alloys

Flexible Monolithic 2-Terminal Kesterite Cu2ZnSnSe4 /perovskite Tandem Solar Cells

Antimony incorporated flexible Cu 2 ZnSn(S,Se) 4 solar cell for enhanced mechanical endurance and efficiency

N‐Type Surface Design for p‐Type CZTSSe Thin Film to Attain High Efficiency

Structural, Electronic and Defect Properties of Cu<sub>2</sub>ZnSn(S,Se)<sub>4</sub> Alloys

In-doping collaboratively controlling back interface and bulk defects to achieve efficient flexible CZTSSe solar cells

Over 10% Efficiency Pure Sulfide Kesterite Solar Cells on Transparent Electrode with Cd-Ag Co-Alloying

A new approach for alkali incorporation in Cu2ZnSnS4 solar cells

10.24% Efficiency of Flexible Cu2 ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

Impact of Cation Substitution in (Ag x Cu 1− x ) 2 ZnSnSe 4 Absorber‐Based Solar Cells toward 10% Efficiency: Experimental and Theoretical Analyses

Cadmium‐Free Kesterite Thin‐Film Solar Cells with High Efficiency Approaching 12%

Beyond 11% Efficient Cu2ZnSn(Se,S)(4) Thin Film Solar Cells by Cadmium Alloying

Efficiency Enhancement of Cu2ZnSn(S,Se)4 Solar Cells via Alkali Metals Doping