Abstract:A novel heterogeneous lamella (HL) design strategy was proposed to improve mechanical properties of a new cost-effective Fe 35 Ni 35 Cr 25 Mo 5 compositionally complicated alloy (CCA). A HL structure was produced by single-step heat treatment (800 °C for 1h) after cold rolling. This HL structure consists of alternative lamellae regions of coarse-grained FCC matrix (5∼20 μm), and regions containing ultra-fine grains or subgrains (200∼500 nm) together with nanoprecipitates (20-500 nm) and annealing twins. The 800 °C annealed sample with HL structure demonstrated a superior tensile property, with yield strength over 1.0 GPa and ductility of ~13%. Formation of the annealing twins and nanoprecipitates decorated HL structure was a result of the concurrent partial recrystallization and precipitation of σ phase at the shear bands with a high density of lattice defects (e.g. high-density dislocation walls and deformation twins). The latter restricted the growth of recrystallized grains, leading to the formation of ultrafine subgrains within the HL structure. The high yield strength resulted from the multistage hetero-deformation induced (HDI) strengthening and precipitation strengthening associated with heterogeneous lamella structures containing nanoprecipitates. The ductility was originated from the coexistence of multiple deformation mechanisms, which started with dislocation slip and formation of stacking faults at the initial stage, followed by nano-twinning at the higher strain level. This HL design strategy, comprising of composition and thermomechanical process designs, and the resultant microstructure tuning, open a broader window for development of cost-effective CCAs with enhanced performance.

A hard/soft layered micro-structured CuCrZr alloy with strength, ductility and electrical conductivity synergy

A dual heterogeneous laminated microstructure design for improving the mechanical properties and electrical conductivity of copper alloys

Inherent and Multiple Strain Hardening Imparting Synergistic Ultrahigh Strength and Ductility in a Low Stacking Faulted Heterogeneous High-Entropy Alloy

Achieving high strength and high conductivity synergy through hierarchical precipitation stimulated structural heterogeneities in a Cu-Ag-Zr alloy

Hierarchical Structured Zn-Cu-Li Alloy with High Strength and Ductility and Its Deformation Mechanisms

Enhanced strength-ductility synergy of Al/Zn/Al laminated composite with unique interface and multi-modal heterogeneous microstructure

Enhanced Hardness Via Interface Alloying in Nanoscale Cu/Al Multilayers

Hierarchical 3D Nanolayered Duplex-Phase Zr with High Strength, Strain Hardening, and Ductility.

Achieving Heterogeneous Structure in Hcp Zr Via Electroplastic Rolling

A promising structure for fabricating high strength and high electrical conductivity copper alloys

A High Strength and High Conductivity Cu0.4Cr0.3Zr Alloy Prepared by Cryo-ECAP and Heat Treatment

Breaking the Strength-Ductility Trade-off Via Heterogeneous Structure in FeCoCrNiMo0.2 High-Entropy Alloy

Effect of layered heterogeneous microstructure design on the mechanical behavior of medium carbon steel

High strength and ductility in a dual-phase hetero-structured AlCoCrFeNi2.1 eutectic high-entropy alloy by powder metallurgy

Heterogeneous Lamella Design to Tune the Mechanical Behaviour of a New Cost-Effective Compositionally Complicated Alloy

Strong and ductile CrCoNi medium-entropy alloy via dispersed heterostructure

Excellent work hardening ability in a novel compositionally complex alloy by hierarchical microstructuring

Heterogeneous Fiberous Structured Mg-Zn-Zr Alloy with Superior Strength-Ductility Synergy

Improving strength-ductility balance of a brittle Al-doped FeCrNi multi-principal element alloy by introducing a heterostructure with hard phase enveloping soft phase

Enhanced strength and ductility of high chromium cast iron/low carbon steel bimetal by heterostructure design

Development of a heterogeneous lamellar structure based on layer instabilities during accumulative roll bonding