Abstract:Heterogeneous metallic structures constitute a novel class of materials with excellent mechanical properties. However, the existing process for obtaining heterostructures from a single material does not meet large-scale industrial requirements. In this study, a pure copper heterostructured laminate (HSL) composed of a surface elongated-grain layer and a central equiaxed-grain layer was fabricated by rolling bonding and annealing. To study the effect of the interface on the mechanical properties of gradient-structured materials, both laminate metal composite (LMC) and non-composite laminate (NCL) were fabricated by cold-rolling pretreatment of the center layer (60% reduction) and cold-rolling bonding of the whole blank (67% reduction). Then, the HSL was obtained by controlling the post-annealing regimes, the microstructure of each layer was optimized, and a larger degree of microstructural heterogeneities, such as grain size, misorientation angle, and grain orientation, was obtained, which resulted in obvious mechanical differences. Tensile tests of the HSL, surface layer, center layer, and NCL specimens revealed that the HSL annealed at 300 °C for 1 h had a significantly higher strength than the center layer and a higher elongation than the surface layer. The HSL had a tensile strength and elongation at fracture of 278.08 MPa and 46.2%, respectively, indicating a good balance of strength and plasticity. The improved properties were primarily attributed to the strengthening or strain hardening due to the inhomogeneous deformation of the heterogeneous layers in the laminate and the mutual constraint acquired by the distinct layers with strong mechanical differences. The HSL had an interfacial bonding strength of 178.5 MPa, which played a vital role in the coordinated deformation of the heterogeneous layers. This study proposes an HSL design method that effectively simplifies the process of obtaining heterostructures in homogeneous materials by controlling the cumulative deformation of the surface and center layers.

A dual heterogeneous laminated microstructure design for improving the mechanical properties and electrical conductivity of copper alloys

High Strength and High Ductility Copper Obtained by Topologically Controlled Planar Heterogeneous Structures

Towards enhanced strength-ductility in pure copper by fabricating hetero grain composite laminates

A hard/soft layered micro-structured CuCrZr alloy with strength, ductility and electrical conductivity synergy

Mechanical Properties Optimization and Microstructure Analysis of Pure Copper Heterostructured Laminates via Rolling

Achieving high strength and high conductivity synergy through hierarchical precipitation stimulated structural heterogeneities in a Cu-Ag-Zr alloy

Additively Manufactured Copper Alloy with Heterogeneous Nanoprecipitates-Dislocation Architecture for Superior Strength-Ductility-Conductivity Synergy

A promising structure for fabricating high strength and high electrical conductivity copper alloys

Development of a heterogeneous lamellar structure based on layer instabilities during accumulative roll bonding

Dual heterogeneous Cu–Al 2 O 3 /Cu laminated composite with high strength and ductility prepared by accumulative roll bonding

Heterogeneous Lamella Design to Tune the Mechanical Behaviour of a New Cost-Effective Compositionally Complicated Alloy

Mechanical properties and fracture behavior in copper-brass heterostructured fibers

Enhanced strength-ductility synergy of Al/Zn/Al laminated composite with unique interface and multi-modal heterogeneous microstructure

Simultaneous enhancement of strength and conductivity via self-assembled lamellar architecture

Investigation of Mechanical Properties and Microstructural Evolution in Pure Copper with Dual Heterostructures Produced by Surface Mechanical Attrition Treatment

The synergistic effects of heterogeneous structures enhance the strength-ductility of Al-Cu composites

Electropulsing-enhanced atomic diffusion and recrystallization to optimize mechanical properties of Al/Cu laminated metal composites

Microstructure and Properties of High Strength and High Conductivity Cu-0.4Mg Alloy Processed by Upward Continuous Casting and Multi-pass Drawing

Enhancing the interface strength of additively manufactured 316 L/CuSn10 bimetallic components through heterogeneous microstructures

Recent development of advanced precipitation-strengthened Cu alloys with high strength and conductivity: A review

Microstructures and mechanical properties of Cu–Ti alloys with ultrahigh strength and high ductility by thermo-mechanical treatment