Abstract:Heterogeneous metallic structures constitute a novel class of materials with excellent mechanical properties. However, the existing process for obtaining heterostructures from a single material does not meet large-scale industrial requirements. In this study, a pure copper heterostructured laminate (HSL) composed of a surface elongated-grain layer and a central equiaxed-grain layer was fabricated by rolling bonding and annealing. To study the effect of the interface on the mechanical properties of gradient-structured materials, both laminate metal composite (LMC) and non-composite laminate (NCL) were fabricated by cold-rolling pretreatment of the center layer (60% reduction) and cold-rolling bonding of the whole blank (67% reduction). Then, the HSL was obtained by controlling the post-annealing regimes, the microstructure of each layer was optimized, and a larger degree of microstructural heterogeneities, such as grain size, misorientation angle, and grain orientation, was obtained, which resulted in obvious mechanical differences. Tensile tests of the HSL, surface layer, center layer, and NCL specimens revealed that the HSL annealed at 300 °C for 1 h had a significantly higher strength than the center layer and a higher elongation than the surface layer. The HSL had a tensile strength and elongation at fracture of 278.08 MPa and 46.2%, respectively, indicating a good balance of strength and plasticity. The improved properties were primarily attributed to the strengthening or strain hardening due to the inhomogeneous deformation of the heterogeneous layers in the laminate and the mutual constraint acquired by the distinct layers with strong mechanical differences. The HSL had an interfacial bonding strength of 178.5 MPa, which played a vital role in the coordinated deformation of the heterogeneous layers. This study proposes an HSL design method that effectively simplifies the process of obtaining heterostructures in homogeneous materials by controlling the cumulative deformation of the surface and center layers.

Dual heterogeneous Cu–Al 2 O 3 /Cu laminated composite with high strength and ductility prepared by accumulative roll bonding

A dual heterogeneous laminated microstructure design for improving the mechanical properties and electrical conductivity of copper alloys

Enhanced strength-ductility synergy of Al/Zn/Al laminated composite with unique interface and multi-modal heterogeneous microstructure

Towards enhanced strength-ductility in pure copper by fabricating hetero grain composite laminates

Development of a heterogeneous lamellar structure based on layer instabilities during accumulative roll bonding

The synergistic effects of heterogeneous structures enhance the strength-ductility of Al-Cu composites

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

Texture characteristics and tensile deformation behavior of Cu/Al layered composites prepared by cast-rolling method

Interface evolution and strengthening of two-step roll bonded cu/Al clad composites

Preparation of heterogeneous nanolaminated graphene nanosheet/Al–Cu–Mg composites by powder assembly & alloying

Microstructure and Mechanical Properties of Al-Mg-Si Similar Alloy Laminates Produced by Accumulative Roll Bonding

Characterization of the interfacial micro-zones in C18150Cu/8011Al laminated composites

High Strength and Thermal Stability of Multilayered Cu/Al Composites Fabricated Through Accumulative Roll Bonding and Cryorolling

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Mechanical Properties Optimization and Microstructure Analysis of Pure Copper Heterostructured Laminates via Rolling

Design a Ti6Al4Vâ€“Ti43Al9V laminated composite with high strength and fracture toughness

Effect of Al2Cu constituent layer thickness discrepancy on the tensile mechanical behavior of Cu/Al2Cu/Al layered composites: A molecular dynamics simulation

Extra strengthening and strain hardening in coarse-grain/ultrafine-grain laminates

Novel laminated multi-layer graphene/Cu–Al–Mn composites with ultrahigh damping capacity and superior tensile mechanical properties

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Heterogeneous lamella structure design to simultaneously strengthen and toughen aluminum alloys