Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

Effect of Al2Cu constituent layer thickness discrepancy on the tensile mechanical behavior of Cu/Al2Cu/Al layered composites: A molecular dynamics simulation

Atomic-scale deformation mechanisms of nano-polycrystalline Cu/Al layered composites: a molecular dynamics simulation

Micromechanical Simulation on Strength and Ductility of Two Kinds of Al-based Nanostructural Materials

Texture characteristics and tensile deformation behavior of Cu/Al layered composites prepared by cast-rolling method

Molecular dynamics studies of the effect of intermediate Fe layer thickness on the enhanced strength and ductility of Cu/Fe/Ni multilayer

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

Ultra-high strength and plasticity mediated by partial dislocations and defect networks: Part II: Layer thickness effect

Uniaxial Tension Deformation Study of Copper/nickel Laminated Composites: Effects of Lamella Number and Interlamellar Spacing

Characterization of the interfacial micro-zones in C18150Cu/8011Al laminated composites

Microstructures and Mechanical Properties of Laminated Structural Nb-Ti-Al Composites Fabricated by Laser Deposition

Layer structure-based grain refinement mechanism and its effect on the mechanical behavior of Ti/Al laminated metal composites

Dual heterogeneous Cu–Al 2 O 3 /Cu laminated composite with high strength and ductility prepared by accumulative roll bonding

Effect of atomic diffusion on interfacial heat transfer and tensile property of copper/aluminum composites

The crucial role of accumulated strain and Cu content on the electrical, thermal, tensile, fracture, and microstructure characteristics of Al/Cu multi-layered composites subjected to SPD

Influence of interface on deformation compatibility of a heterogeneous Cu/Al nanoscale multilayer

Biomimetic Layered Fiber-Reinforced Ti–Al Composites: Effects of Various Parameters on Their Strength and Ductility Through Finite Element Analysis

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate

Microstructure and Mechanical Properties of Ti-Al-Ti-Ti2AlNb Laminated Composites Based on the Ductile-brittle Structure

Effects of Ni Foil Thickness on the Microstructure and Tensile Properties of Reaction Synthesized Multilayer Composites

Molecular Dynamics Studies on Size Effects in Laminated Polycrystalline Graphene/Copper Composites: Implications for Mechanical Behavior