Abstract:In this study, the accumulative roll bonding (ARB) method, a severe plastic deformation (SPD) process, was used to fabricate copper-2 wt% silicon carbide composite strips. The ARB process was successfully conducted for up to nine cycles on pure copper strips with silicon carbide particles distributed between them, as well as on monolithic copper. Equiaxed tensile and Vickers hardness tests were conducted to evaluate the mechanical properties of the samples. SEM was utilized to study the fracture surfaces and to determine the fracture mechanism of ARB processed monolithic copper and composite samples after the tensile test. Texture parameters were calculated through X-ray analysis. The Rietveld method using MAUD software were employed to assess the crystallite size of the samples. Results indicated that average amount of porosity decreased and interface bonding between copper strip layers improved with increasing the number of ARB cycles. Moreover, an increased number of cycles led to homogeneous distribution of SiC particles within the copper matrix. The tensile strength of the fabricated composites improved with an increase in the number of cycles, ultimately reaching 483 MPa after nine cycles, compared to 388 MPa for the composite processed with a single cycle of ARB and 194 MPa for annealed copper strips. Initially, the elongation of the composite samples decreased dramatically to about 6% after applying five cycle of ARB process from the 46% observed for annealed pure copper strip. However, it improved as the process continued, reaching 8.9% after the ninth cycle. Investigation of fracture surfaces after the tensile test using SEM revealed that the dominant failure mode was shear ductile fracture. Analysis of sample textures demonstrated that the dominant texture was (100). Crystallite sizes for pure copper and nine cycles-rolled composites, as determined by Reitveld method, reached 111 nm and 89 nm, respectively.

The crucial role of accumulated strain and Cu content on the electrical, thermal, tensile, fracture, and microstructure characteristics of Al/Cu multi-layered composites subjected to SPD

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Texture characteristics and tensile deformation behavior of Cu/Al layered composites prepared by cast-rolling method

Effect of normal load and strain accumulation on tribological properties of Al3003/St12 multilayered composite produce by severe plastic deformation

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

Effect of Heat Treatment on the Interfacial Structure and Microstructure of Al/Al/Cu Composites Prepared by Different Accumulative Roll Bonding Passes

Microstructure, Mechanical and Thermal Properties of Al/Cu/SiC Laminated Composites, Fabricated by the ARB and CARB Processes

Characteristic Investigation of Trilayered Cu/Al8011/Al1060 Composite: Interface Morphology, Microstructure, and In-Situ Tensile Deformation

Microstructure and mechanical properties of Al/Cu/Mg laminated composite sheets produced by the ARB proces

Effects of Cr addition on the microstructural, mechanical and electrical characteristics of Cu–6wt.%Ag microcomposite

Effect of Al2Cu constituent layer thickness discrepancy on the tensile mechanical behavior of Cu/Al2Cu/Al layered composites: A molecular dynamics simulation

The Effect of Cu Content on the Microstructure and Properties of the Wire Arc Additive Manufacturing Al-Cu Alloy

Effect of ARB process on the plane stress fracture toughness, creep properties and forming limit diagram of Aluminum/BN/Copper composite strips

Experimental and Numerical Analysis of Cu/Al8011/Al1060 Trilayered Composite: a Comprehensive Study

Characterization of the interfacial micro-zones in C18150Cu/8011Al laminated composites

Structural and mechanical properties of Cu-SiCp nanocomposites fabricated by accumulative roll bonding (ARB)

Fabrication of nanostructured Al/Cu/Mn metallic multilayer composites by accumulative roll bonding process and investigation of their mechanical properties

A study on the microstructural evolution of copper/aluminum composite strips fabricated by micro flexible rolling

Structural characteristics and corrosion properties of Cu/Sn–Pb composite produced by accumulative roll bonding process