Abstract:With the advancement of science and technology and the construction of metal-based composites (MMC), it became possible to achieve improved properties that were not easily available in an alloy. In fact, with the emergence of such technology, manufacturers were able to adjust the resulting materials according to their needs in such a way as to provide mechanical strength, hardness, corrosion resistance, or other desired properties. These composites were used in various aerospace, automotive, construction, and production industries. Aluminum-based composites are among the structures that have taken an important place in the industry due to their lightweight and high strength. The present study produced bi-alloy aluminum-based 1060/5083 composites fabricated with alumina particles with a Hot ARBp at T = 380 °C. Also, the effect of rolling steps on the roll bonding mechanism is investigated using numerical simulation. As the novelty of this study and for the first time, a bi-alloy 1050/5083 composites reinforced Al 2 O 3 particles via ARB process have been produced and then, potential dynamic polarization in 3.5 Wt% NaCl solution was used to study the corrosion properties of these composites. The corrosion behavior of these samples was compared and studied with that of the annealed aluminum. The study aimed to investigate the bonding behavior between the bi-alloy layers. So, as a result of enhancing influence on the number of ARBp, this experimental investigation revealed a significant enhancement in the main electrochemical parameters and the inert character of the Alumina particles. Reducing the active zones of the material surfaces could delay the corrosion process. Results showed that the corrosion resistance of the sample fabricated after six steps improved more than 100 % in comparison with the initial annealed Al alloy. Also, the average peeling force improved from 45 N to 94 N for the sample fabricated with six steps. Moreover, at a higher number of steps, the corrosion of MMC improved. Moreover, increasing the number of ARBsteps illustrated an improvement in the wear resistance of samples. Finally, the samples' bonding interface, corrosion surface, and peeled surface were investigated using scanning electron microscopy (SEM).

Microstructure and mechanical properties of Al/Cu/Mg laminated composite sheets produced by the ARB proces

Fabrication of nanostructured Al/Cu/Mn metallic multilayer composites by accumulative roll bonding process and investigation of their mechanical properties

Roll bonding characteristics of the Mg/Zn/Cu/Al multilayered composite produced by the ARB process

Mechanical, microstructural, and textural evaluation of aluminum-MWCNT composites manufactured via accumulative roll bonding at ambient condition

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Microstructure, Mechanical and Thermal Properties of Al/Cu/SiC Laminated Composites, Fabricated by the ARB and CARB Processes

Comprehensive investigation on wear and microstructure development in Al/ti ultrafine grained multi-layered composite produced by Accumulative Roll Bonding (ARB)

Forming limit diagrams and mechanical properties of AA1050/Ti CP2 multilayered composite produced by the accumulative roll bonding technique

Preparation, Microstructure, and Mechanical Properties of Aluminum Matrix Composite by Accumulating Roll Bonding Method

Microstructure evolution and mechanical behavior of α/β alternative Mg–Li alloy composite sheets with different initial thickness ratios prepared by accumulative roll bonding

Response mechanism of matrix microstructure evolution and mechanical behavior to Mg/Al composite plate by hard-plate accumulative roll bonding

Microstructure, Mechanical Properties and Strain Hardening Behavior of Alternative α/β Mg-Li Composite Sheets Prepared by Accumulative Roll Bonding

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Microstructure and Mechanical Properties of Al-Mg-Si Similar Alloy Laminates Produced by Accumulative Roll Bonding

Effect of ARB process on the plane stress fracture toughness, creep properties and forming limit diagram of Aluminum/BN/Copper composite strips

Improving strength-ductility synergy of nano/ultrafine-structured Al/Brass composite by cross accumulative roll bonding process

Corrosion and mechanical properties of Al/Al 2 O 3 composites fabricated via accumulative roll bonding process: Experimental and numerical simulation

Effect of Asymmetric Accumulative Roll-Bonding process on the Microstructure and Strength Evolution of the AA1050/AZ31/AA1050 Multilayered Composite Materials

The crucial role of accumulated strain and Cu content on the electrical, thermal, tensile, fracture, and microstructure characteristics of Al/Cu multi-layered composites subjected to SPD

Enhancing grain refinement and mechanical properties of AA1100/MgAZ31/AA1100 composites by using different roll bonding techniques

Optimization mechanism of matrix microstructure evolution on strength-plasticity of Mg/Al composite plate during hard-plate accumulative roll bonding