Abstract:Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Ahead of Print. In this study, the AA1050/Ti CP2 metallic multilayered composite was produced by accumulative roll bonding (ARB) using AA 1050 and commercially pure titanium Ti (CP-Ti ASTM grade 2) for three cycles at ambient temperature. The microstructure evolution was investigated by scanning electron microscopy (SEM) equipped with an energy dispersive spectrometer (EDS) and X-ray diffraction (XRD). Also, the tensile test and Vickers microhardness measurement were conducted to evaluate mechanical properties. The forming limit diagrams (FLD) were obtained for a metallic multilayered composite for the first time by the Nakazima test. It was observed that a continuous and well-bonded composite was fabricated after the first cycle. For the subsequent two cycles, necking and fracture of Ti reinforcement occurred in the Al matrix. The maximum tensile strength was reached after two cycles with almost a 98% increase compared to the annealed aluminum sample. However, the tensile strength was reduced after the third cycle. The uniform elongation considerably decreased after the first cycle and was maintained for the subsequent two cycles. The microhardness improved by 124% and 47% for Al and Ti, respectively, in the whole process of ARB in comparison with annealed Al and Ti. As a formability criterion, the level of forming limit curve (FLC) was reduced sharply after the first ARB cycle. For subsequent cycles, this reduction was neglectable. The Al/Ti composite fracture surfaces were a combination of shear ductile and brittle after the third pass.

Comprehensive investigation on wear and microstructure development in Al/ti ultrafine grained multi-layered composite produced by Accumulative Roll Bonding (ARB)

Forming limit diagrams and mechanical properties of AA1050/Ti CP2 multilayered composite produced by the accumulative roll bonding technique

Study of mechanical properties and wear resistance of nanostructured Al 1100/TiO2 nanocomposite processed by accumulative roll bonding

Fabrication of nanostructured Al/Cu/Mn metallic multilayer composites by accumulative roll bonding process and investigation of their mechanical properties

Microstructure and mechanical properties of Al/Cu/Mg laminated composite sheets produced by the ARB proces

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Mechanical, microstructural, and textural evaluation of aluminum-MWCNT composites manufactured via accumulative roll bonding at ambient condition

Microstructure and Mechanical Properties of Ultra-Lightweight Mg-Li-Al/Al-Li Composite Produced by Accumulative Roll Bonding at Ambient Temperature

Fracture toughness, wear, and microstructure properties of aluminum/titanium/steel multi-laminated composites produced by cross-accumulative roll-bonding process

Microstructure and Mechanical Properties of the Mg/Al Laminated Composite Fabricated by Accumulative Roll Bonding (Arb)

Microstructural Evolution during Continuous Heating of Multilayered Al/Fe Metallic Composite Processed by Accumulative Roll Bonding

Study of changes in the aging process, microstructure, and mechanical properties of AA2024-AA1050 nanocomposites created by the accumulative roll bonding process, with the addition of 0.005 vol.% of alumina nanoparticles

Preparation, Microstructure, and Mechanical Properties of Aluminum Matrix Composite by Accumulating Roll Bonding Method

CORROSION, WEAR AND MECHANICAL PROPERTIES OF LAMINATED Al/TiC COMPOSITES

Microstructure and tribological behavior of Al-TiC composite strips fabricated by a multi-step densification method

Microstructural evolution and mechanical properties of accumulative roll bonded interstitial free steel

Evolution of Microstructure, Texture and Mechanical Properties for Multilayered Al Matrix Composites by Accumulative Roll Bonding

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Effect of normal load and strain accumulation on tribological properties of Al3003/St12 multilayered composite produce by severe plastic deformation

Microstructure, Mechanical and Thermal Properties of Al/Cu/SiC Laminated Composites, Fabricated by the ARB and CARB Processes

On the impact of using alumina nanoparticles and initial aging on the microstructure and mechanical properties of the AA1050/AA2024 nanostructure composite, created by accumulative roll bonding (ARB) method