Abstract:In order to understand the strengthening and the failure mechanism of accumulative roll bonding (ARB)-processed AZ63 Mg alloy, the interfacial bonding and fracture behavior of an ARB-processed AZ63 sheet were studied through electron microscopic analysis. The correlation between the mechanical properties, the microstructure, and the ARB processing parameters of an AZ63 sheet were presented. The experimental results have demonstrated that the average grain size of AZ63 Mg alloy processed by ARB was remarkably refined from 12.8 μm to 5.7 μm when the ARB processing temperature was set to 623 K, indicating the occurrence and development of dynamic recrystallization (DRX) nucleation. With the increase in ARB passes, the microstructure obviously became uniform. However, after five passes of the ARB process at 623 K, grains with different crystallographic orientations at the interface can be rearranged to generate the coherent eutectic plane, which inhibits the further refinement of grain size. During the ARB process of the AZ63 Mg alloy, the grain refinement was controlled by twin-induced recrystallization and dynamic recrystallization. Microcracks at the bonded interface of the ARB1 sample were eliminated during the following 3~5 rolling passes at 623 K. After three passes of the ARB process at 623 K, the strength and elongation of the AZ63 Mg alloy increased from 232 MPa and 18.5% to 282 MPa and 26.3%, respectively. The tensile fracture morphology of the sample processed by three passes of ARB exhibited numerous dimples, and the slip lines caused by the cooperative deformation of refined grains can produce a network-like dimple structure, indicating that excellent ductile fracture characteristics could be obtained.

Microstructural Evolution and Mechanical Properties of Multi-layered Aluminum Alloy 6061 Processed by Accumulative Roll Bonding

Enhancing of aluminum alloy 1050-H4 tensile strength by accumulative roll bonding process

Microstructure Evolution and Mechanical Properties of AZ31 Alloy with Accumulative Roll Bonding

Microstructural evolution and mechanical properties of multilayered ARB6/3/6 2N Al processed by accumulative roll bonding

Enhancement of strength and ductility in 6061Al alloy processed by cross accumulative roll bonding

Evolution of texture and microstructure during accumulative roll bonding of aluminum AA5086 alloy

Interfacial Bonding and Fracture Behaviors of AZ63 Magnesium Alloy Sheet Processed by Accumulative Roll Bonding

Enhancing grain refinement and mechanical properties of AA1100/MgAZ31/AA1100 composites by using different roll bonding techniques

Preparation, Microstructure, and Mechanical Properties of Aluminum Matrix Composite by Accumulating Roll Bonding Method

Microstructure of Commercial-Purity Aluminum Sheets Processed by Accumulative Roll Bonding (ARB) at a Series of Cyclic Preheating Conditions

Corrosion Behavior of Ultra-fine Grained 1050 Aluminum Alloy Fabricated by ARB Process in a Buffer Borate Solution

Revealing the evolution mechanisms of microstructure, texture and mechanical behavior in Zr702 alloy plates fabricated by accumulative roll bonding

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Microstructure and mechanical properties of AA1050/AA6061 multilayer composites via accumulative roll bonding and cryorolling and subsequent aging

Texture and Mechanical Anisotropy of Ultrafine-Grained Aluminum Alloy AA6016 Produced by Accumulative Roll Bonding

Microstructure and mechanical properties of ARB-processed AA1050/AA5052 multilayer laminate sheets during cryorolling

Effect of Asymmetric Accumulative Roll-Bonding process on the Microstructure and Strength Evolution of the AA1050/AZ31/AA1050 Multilayered Composite Materials

Microstructural evolution and mechanical properties of accumulative roll bonded interstitial free steel

Grain refinement and mechanical properties of pure aluminum processed by accumulative extrusion bonding

Mechanical, microstructural, and textural evaluation of aluminum-MWCNT composites manufactured via accumulative roll bonding at ambient condition