Abstract:With the advancement of science and technology and the construction of metal-based composites (MMC), it became possible to achieve improved properties that were not easily available in an alloy. In fact, with the emergence of such technology, manufacturers were able to adjust the resulting materials according to their needs in such a way as to provide mechanical strength, hardness, corrosion resistance, or other desired properties. These composites were used in various aerospace, automotive, construction, and production industries. Aluminum-based composites are among the structures that have taken an important place in the industry due to their lightweight and high strength. The present study produced bi-alloy aluminum-based 1060/5083 composites fabricated with alumina particles with a Hot ARBp at T = 380 °C. Also, the effect of rolling steps on the roll bonding mechanism is investigated using numerical simulation. As the novelty of this study and for the first time, a bi-alloy 1050/5083 composites reinforced Al 2 O 3 particles via ARB process have been produced and then, potential dynamic polarization in 3.5 Wt% NaCl solution was used to study the corrosion properties of these composites. The corrosion behavior of these samples was compared and studied with that of the annealed aluminum. The study aimed to investigate the bonding behavior between the bi-alloy layers. So, as a result of enhancing influence on the number of ARBp, this experimental investigation revealed a significant enhancement in the main electrochemical parameters and the inert character of the Alumina particles. Reducing the active zones of the material surfaces could delay the corrosion process. Results showed that the corrosion resistance of the sample fabricated after six steps improved more than 100 % in comparison with the initial annealed Al alloy. Also, the average peeling force improved from 45 N to 94 N for the sample fabricated with six steps. Moreover, at a higher number of steps, the corrosion of MMC improved. Moreover, increasing the number of ARBsteps illustrated an improvement in the wear resistance of samples. Finally, the samples' bonding interface, corrosion surface, and peeled surface were investigated using scanning electron microscopy (SEM).

CORROSION, WEAR AND MECHANICAL PROPERTIES OF LAMINATED Al/TiC COMPOSITES

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Microstructure and tribological behavior of Al-TiC composite strips fabricated by a multi-step densification method

Forming limit diagrams and mechanical properties of AA1050/Ti CP2 multilayered composite produced by the accumulative roll bonding technique

Comprehensive investigation on wear and microstructure development in Al/ti ultrafine grained multi-layered composite produced by Accumulative Roll Bonding (ARB)

Influence of TiC content on mechanical, wear and corrosion properties of hot-pressed AZ91/TiC composites

Wear Behavior of Ti6Al4V Based Hybrid Composites Reinforced with TiB2(7.5%) + TiC (7.5%)

Influence of TiC Particles on Mechanical and Tribological Characteristics of Advanced Aluminium Matrix Composites Fabricated through Ultrasonic-Assisted Stir Casting

Microstructure, Mechanical and Thermal Properties of Al/Cu/SiC Laminated Composites, Fabricated by the ARB and CARB Processes

Microstructure, Corrosion and Mechanical Properties of TiC Particles/Al-5Mg Composite Fillers for Tungsten Arc Welding of 5083 Aluminum Alloy

A novel way to fabricate high elastic modulus and high strength of TiC reinforced aluminum matrix composite

Corrosion and mechanical properties of Al/Al 2 O 3 composites fabricated via accumulative roll bonding process: Experimental and numerical simulation

Microstructure, hardness, and wear resistance of AA5083/Ti3SiC2 composites fabricated via friction stir processing

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance

Integrating Experimental and Computational Analyses for Mechanical Characterization of Titanium Carbide/Aluminum Metal Matrix Composites

Compressive performance and crack propagation in Al alloy/Ti2AlC composites

Tribological Behavior of TiC Particles Reinforced 316Lss Composite Fabricated Using Selective Laser Melting

Wear Performance of TiB2-Reinforced AZ91 Magnesium Metal Matrix Composite Fabricated by Ultrasonic Stir-Casting Process

Fabrication and wear behavior of TiC/TiB 2 -reinforced NiAl intermetallic matrix composites

Study of mechanical properties and wear resistance of nanostructured Al 1100/TiO2 nanocomposite processed by accumulative roll bonding

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment