Abstract:Air‐hardening forging steels are a new steel concept, promising high strength and ductility combinations in combination with a reduced environmental impact. Herein, the effect of the microstructure before intercritical annealing is discussed in regard to microstructure evolution and strain hardening behavior. It is demonstrated that the microstructure prior to intercritical annealing governs the microstructures and final mechanical properties. The influence of different microstructures on the plastic stability of an air‐hardened industrially produced medium‐manganese steel is presented. For this matter, heat treatment parameters before and during intercritical annealing (IA) are varied, to achieve different microstructures. The resulting duplex microstructure is consecutively tested by tensile tests, which are monitored by digital image correlation (DIC) to obtain information on the local plastic deformation. The tests are accompanied by microstructure investigations using optical, scanning electron, and transmission electron microscopy. Finally, X‐ray and electron backscatter diffraction experiments are performed before and after deformation, to describe the altering phase fractions. It is demonstrated that the effect of the deformation temperature prior to IA treatment has a significant influence on the duplex microstructure, as it changes the austenite morphology from lamellar to globular and increases the phase fraction. The change in austenite phase fraction and morphology results in a higher yield strength (≈100 MPa), as well as higher uniform and total elongations (+2% and +5%, respectively). The DIC and tensile tests reveal that these differences in the austenite phase lead to a complete change in the strain hardening behavior, from continuous flow to discontinuous serrated flow, with clearly visible deformation bands during plastic deformation.

Effect of layered heterogeneous microstructure design on the mechanical behavior of medium carbon steel

Regulation on Annealing Multiscale Laminar Structure and Mechanical Characteristics of Plain Medium Carbon Steel by Warm Pre-deformation Extent

Strengthening and Strain Hardening Mechanisms of a Plain Medium Carbon Steel by Multiscale Lamellar Structures

Strength and Ductility Enhancement of Plain Carbon Steel by Heterostructure Design

Stabilized Uniform Deformation in A High-Strength Ferrite-Cementite Steel with Multiscale Lamellar Structure

Enhanced strength and ductility of the low-carbon steel with heterogeneous lamellar dual-phase structure produced by cyclic intercritical rolling

Dual-phase hetero-structured strategy to improve ductility of a low carbon martensitic steel

Heterogeneous Microstructure and Enhanced Mechanical Properties in Annealed Multilayered IF Steel

Effect of Annealing Time on Microstructure Stability and Mechanical Behavior of Ferrite-Cementite Steel with Multiscale Lamellar Structure

Influence of warm rolling temperature on multi-scale lamellar structure and mechanical properties of medium carbon steel

Multiscale Microstructure Evolution and Subgrain Strengthening of Warm-Rolled Ultrafine Pearlite Steel

Ultra-Fine Heterogeneous Microstructure Enables High Strength-Ductility in a Cold-Rolled Medium Mn Steel

Effect of microstructure heterogeneity on the mechanical properties of friction stir welded reduced activation ferritic/martensitic steel

Microstructure Evolution and Mechanical Properties of Medium Carbon Martensitic Steel during Warm Rolling and Annealing Process

Formation of Bimodal-Sized Structure and Its Tensile Properties in a Warm-Rolled and Annealed Ultrafine-Grained Ferrite/Cementite Steel

The Influence of Microstructure and Process Design on the Plastic Stability of 4 wt% Medium‐Manganese Steels

Effect of Central Multiphase Microstructure of Thick Plates on Work Hardening and Crack Propagation

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

Effect of Prior-Austenite Grain Size on the Microstructure and Mechanical Properties of Ultrafine-Grained Dual-Phase Layer-Structured Steel Produced by Hot Rolling of Intercritical Annealed Bainite

Towards Strength-Ductility Synergy in a Medium Mn Steel Through Developing Heterogeneous Dual-Morphology Microstructure

Intercritical Rolling Induced Ultrafine Lamellar Structure and Enhanced Mechanical Properties of Medium-Mn Steel