Abstract:Recently, energy conservation, environmental protection and security are the main factors considered by the automotive manufacturers. Medium-Mn steel with excellent combination of specific strength and ductility have been regarded as the potential candidates for automotive applications. The excellent combination of specific strength and ductility depends on the microstructure under different heat treatment processes of the steels. Therefore, the relationship of the combination of specific strength and ductility and microstructure should be studied in detail. Anew alloy system of aluminum-containing medium-Mn steel was developed in this study. The addition of aluminum stabilizes alpha-ferrite, and facilitates the presence of 6-ferrite during solidification. The addition of Mn and C compensates the effect of aluminum on phase stability and ensures austenite formation. In this investigation, the effects of intercritical annealing temperature on the microstructure and tensile properties of a newly designed cold-rolled aluminum-containing medium-Mn steel (0.2C-5Mn- 0.6Si- 3Al, mass fraction, %) were investigated by SEM, XRD and uniaxial tensile tests. The tensile results show that an excellent combination of ultimate tensile strength (sigma(b)) of 1062 MPa, total elongation (delta) of 58.2% and sigma(b) x delta of 61.8.% could be obtained after annealing at 730 degrees C. The inverted austenite of the cold-rolled steel coarsenes and gradually changes its morphology from mainly lamellar to mainly equiaxed with increasing intercritical annealing temperature, and a duplex microstructure consisting of multi-scale retained austenite could be obtained at 730 degrees C, which possesses suitable mechanical stability and thus presents prolonged transformation-induced plasticity (TRIP) effect during tensile deformation. This kind of sustainable TRIP effect and the cooperative deformation of ferrite are responsible for the superior mechanical properties. The investigation of tensile fracture behavior shows that the nucleation and growth of voids occurred mainly at the interfaces between soft ferrite and hard martensite induced by deformation.

Microstructural evolution and strain hardening behavior of a novel two-stage warm rolled ultra-high strength medium Mn steel with heterogeneous structures

Ultra-Fine Heterogeneous Microstructure Enables High Strength-Ductility in a Cold-Rolled Medium Mn Steel

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Super-High-Strength and Formable Medium Mn Steel Manufactured by Warm Rolling Process

Stepwise Warm Rolling for Synergistic Strength and Ductility Enhancement in Heterolamellar Medium-Mn Steel

Design of a high strength, high ductility 12 wt% Mn medium manganese steel with hierarchical deformation behaviour

Heterogeneous Multi-Phase Grains Improving the Strength-Ductility Balance in Warm-Rolled Fe-18Mn-3Ti Steel

Heterostructure mediated high strength and large ductility in novel medium-Mn steels with low Mn content

Two-stage Rolling and Partial Annealing Enables Heterogeneous Structure and Strength-Ductility Enhancement for Austenitic Stainless Steel

Enhancing strength–ductility synergy in medium Mn steel with hetero-structured austenite developed by two-stage cyclic thermomechanical treatment and flash annealing

Microstructure evolution and mechanical properties of metastable austenitic medium Mn steel fabricated by warm caliber rolling

Tailoring hetero-grained austenite via a cyclic thermomechanical process for achieving ultrahigh strength-ductility in medium-Mn steel

Physical metallurgy of medium-Mn advanced high-strength steels

Towards Strength-Ductility Synergy in a Medium Mn Steel Through Developing Heterogeneous Dual-Morphology Microstructure

Microstructure and Mechanical Properties of Medium Mn Steel Containing 3%al Processed by Warm Rolling

Heterogeneous Fe-Mn-Al-C Lightweight Steel Breaking the Strength-Ductility Trade-off Via High-Temperature Warm Rolling Process

Multiscale Microstructure Evolution and Subgrain Strengthening of Warm-Rolled Ultrafine Pearlite Steel

Heterogeneous Multiphase Microstructure Formation through Partial Recrystallization of a Warm-Deformed Medium Mn Steel during High-Temperature Partitioning

High strength and ductility combination in nano-/ultrafine-grained medium-Mn steel by tuning the stability of reverted austenite involving intercritical annealing

Microstructure evolution and tensile behaviour of a cold rolled 8 wt\% Mn medium manganese steel

Effect of hot/warm rolling on the microstructures and mechanical properties of medium-Mn steels