Abstract:Medium Mn steels are promising candidates for the third-generation advanced high strength steels. However, it shows a distinct limit of mechanical property under conventional hot-rolling and intercritical annealing procedures. Aiming at improving the combination of strength, ductility and toughness, the present study proposed a multi-alloyed design principle together with a direct intercritical rolling process. The results show that the microstructure of the hot rolled steel consisted of wide delta ferrite, lath martensite, twinned-martensite and coarse retained austenite with a low stability, corresponding to a product of strength and elongation (PSE) of 24.0 GPa% and an impact toughness of 13.8 J/cm 2 at −40 °C. In contrast, the intercritical rolling produced a laminated microstructure containing thin delta ferrite, submicron recrystallized ferrite and retained austenite. The PSE and impact toughness at −40 °C simultaneously increased to 46.1 GPa% and 46.7 J/cm 2 , respectively, which was also much higher than the hot rolled steel subjected to low temperature and high temperature annealing. The significant enhancement of mechanical property was mainly attributed to the highest content and optimal stability of retained austenite caused by the submicron grain size, high density of dislocations, granular morphology, and elemental enrichment. The optimized austenite stability provided persistent transformation-induced plasticity (TRIP) effect for work hardening and damage resistance. Moreover, the nano-sized VC precipitates in the intercritical rolled steel played a significant role in reaching an ultrahigh yield strength of ∼1 GPa. This study not only provides a very simple pathway to improve the mechanical property of medium Mn steel, but also sheds light on the design and development of high-performance materials.

Tailoring hetero-grained austenite via a cyclic thermomechanical process for achieving ultrahigh strength-ductility in medium-Mn steel

Austenite Tailoring for Strength and Ductility Enhancement in Medium Mn Steel: A Brief Review

Enhancing strength–ductility synergy in medium Mn steel with hetero-structured austenite developed by two-stage cyclic thermomechanical treatment and flash annealing

Tailoring the metastable reversed austenite from metastable Mn-rich carbides

Heterostructure mediated high strength and large ductility in novel medium-Mn steels with low Mn content

Tailoring Heterogeneous Microstructure in a High-Strength Low-Alloy Steel for Enhanced Strength-Toughness Balance

High strength and ductility combination in nano-/ultrafine-grained medium-Mn steel by tuning the stability of reverted austenite involving intercritical annealing

Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Ultra-Fine Heterogeneous Microstructure Enables High Strength-Ductility in a Cold-Rolled Medium Mn Steel

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Achieving Excellent Strength–Ductility Synergy by Tailoring the Grain Size Distribution in a Metastable Austenitic Stainless Steel

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength

Design of a high strength, high ductility 12 wt% Mn medium manganese steel with hierarchical deformation behaviour

Ensuring the strength and ductility synergy in an austenitic stainless steel: single- or multi-phase hetero-structures design

Heterogeneous Multiphase Microstructure Formation through Partial Recrystallization of a Warm-Deformed Medium Mn Steel during High-Temperature Partitioning

Design of Tri-Phase Lamellar Architectures for Enhanced Ductility in Ultra-Strong Steel

Tailoring the deformation behaviour of a medium Mn steel through isothermal intercritical annealing

Microstructural evolution and strain hardening behavior of a novel two-stage warm rolled ultra-high strength medium Mn steel with heterogeneous structures

Enhancing strength and ductility in heterolamellar medium-Mn steel through bamboo-like microstructure design

Constructing multi-scale retained austenite makes bainitic steel better mechanical properties by introducing weak chemical heterogeneity