Abstract:Air‐hardening forging steels are a new steel concept, promising high strength and ductility combinations in combination with a reduced environmental impact. Herein, the effect of the microstructure before intercritical annealing is discussed in regard to microstructure evolution and strain hardening behavior. It is demonstrated that the microstructure prior to intercritical annealing governs the microstructures and final mechanical properties. The influence of different microstructures on the plastic stability of an air‐hardened industrially produced medium‐manganese steel is presented. For this matter, heat treatment parameters before and during intercritical annealing (IA) are varied, to achieve different microstructures. The resulting duplex microstructure is consecutively tested by tensile tests, which are monitored by digital image correlation (DIC) to obtain information on the local plastic deformation. The tests are accompanied by microstructure investigations using optical, scanning electron, and transmission electron microscopy. Finally, X‐ray and electron backscatter diffraction experiments are performed before and after deformation, to describe the altering phase fractions. It is demonstrated that the effect of the deformation temperature prior to IA treatment has a significant influence on the duplex microstructure, as it changes the austenite morphology from lamellar to globular and increases the phase fraction. The change in austenite phase fraction and morphology results in a higher yield strength (≈100 MPa), as well as higher uniform and total elongations (+2% and +5%, respectively). The DIC and tensile tests reveal that these differences in the austenite phase lead to a complete change in the strain hardening behavior, from continuous flow to discontinuous serrated flow, with clearly visible deformation bands during plastic deformation.

Tailoring the deformation behaviour of a medium Mn steel through isothermal intercritical annealing

High strength and ductility combination in nano-/ultrafine-grained medium-Mn steel by tuning the stability of reverted austenite involving intercritical annealing

Intercritical annealing to achieve a positive strain-rate sensitivity of mechanical properties and suppression of macroscopic plastic instabilities in multi-phase medium-Mn steels

Experimental Investigation on a Novel Medium Mn Steel Combining Transformation-Induced Plasticity and Twinning-Induced Plasticity Effects

Tailoring hetero-grained austenite via a cyclic thermomechanical process for achieving ultrahigh strength-ductility in medium-Mn steel

Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling

Intercritically Annealed Medium-Manganese Steel: Insights into Microstructural and Microtextural Evolution, Strain Distribution, and Grain Boundary Characteristics

The Influence of Microstructure and Process Design on the Plastic Stability of 4 wt% Medium‐Manganese Steels

Influence of Intercritical Annealing on Microstructure, Ductility, and Toughness of Medium Mn Steels

Ensuring Combination of Strength, Ductility and Toughness in Medium-Manganese Steel Through Optimization of Nano-Scale Metastable Austenite

Effect of a two-step annealing process on deformation-induced transformation mechanisms in cold-rolled medium manganese steel

Regulation on Annealing Multiscale Laminar Structure and Mechanical Characteristics of Plain Medium Carbon Steel by Warm Pre-deformation Extent

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Improving the Ductility of Ultrahigh-Strength Medium Mn Steels Via Introducing Pre-Existed Austenite Acting As a "reservoir" for Mn Atoms

Tailoring the metastable reversed austenite from metastable Mn-rich carbides

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

Effect of Deformed Prior Austenite Characteristics on Reverse Phase Transformation and Deformation Behavior of High-Strength Medium-Mn Steel

Extra Work Hardening in Room-Temperature Quenching and Partitioning Medium Mn Steel Enabled by Intercritical Annealing

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength

The Significant Influence of Cooling Rate and Intercritical Annealing Temperature on Austenite Stability and Relationship to Mechanical Behavior in Medium Manganese Steel

On the Formability of Medium Mn Steel Treated with Varied Thermal Processing Routes