Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

The Influence of Microstructure and Process Design on the Plastic Stability of 4 wt% Medium‐Manganese Steels

Influence of Alloying Elements on the Dynamic Recrystallization of 4 wt.-% Medium Manganese Steels

Influence of Intercritical Annealing on Microstructure, Ductility, and Toughness of Medium Mn Steels

Increase in Low-Carbon Steel 12GBA Strength and Cold Resistance by a Deformation-Thermal Effect

The impact of intercritical annealing temperature on microstructure and mechanical properties of an ultra-low carbon medium manganese heavy steel plates

Effect of Intercritical Annealing Time on Microstructure Evolution and Mechanical Properties of Low Carbon Medium Manganese Steel Subjected to Multi-Step Heat Treatment Process

Effect of Deformed Prior Austenite Characteristics on Reverse Phase Transformation and Deformation Behavior of High-Strength Medium-Mn Steel

Tailoring the deformation behaviour of a medium Mn steel through isothermal intercritical annealing

The influence of annealing temperature on the microstructure and mechanical properties of Fe-0.52C-11Mn-5.14Al-1Cr lightweight Steel

Intercritically Annealed Medium-Manganese Steel: Insights into Microstructural and Microtextural Evolution, Strain Distribution, and Grain Boundary Characteristics

Effects of plasticity-induced martensitic transformation and grain refinement on the evolution of microstructure and mechanical properties of a metastable high entropy alloy

Enhancing strength–ductility synergy in medium Mn steel with hetero-structured austenite developed by two-stage cyclic thermomechanical treatment and flash annealing

Achieving an excellent combination of strength and plasticity in a low carbon steel through dynamic plastic deformation and subsequent annealing

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Intercritical annealing to achieve a positive strain-rate sensitivity of mechanical properties and suppression of macroscopic plastic instabilities in multi-phase medium-Mn steels

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Physical metallurgy of medium-Mn advanced high-strength steels

Microstructural characteristics and tensile behavior of medium manganese steels with different manganese additions

Effect of layered heterogeneous microstructure design on the mechanical behavior of medium carbon steel

The influence of cooling methods on the austenite stability and plastic instability behavior in 3Mn steel