Abstract:This paper describes the main results from an experimental investigation into tailoring the phase content and grain structure for high strength of a microstructurally flexible high entropy alloy (HEA), Fe42Mn28Co10Cr15Si5 (in at%), using rolling, friction stir processing (FSP), and compression. Optical microscopy, neutron diffraction, and electron backscatter diffraction were employed to characterize microstructure and texture evolution. The material upon rolling was found to have triplex structure consisting of metastable gamma austenite (γ), stable sigma (σ), and stable epsilon martensite (ε) phases. The adaptive phase stability exhibited by the selected HEA of very low stacking fault energy with strain, strain rate, and temperature was used along with grain refinement to enhance the strength. To this end, the complex structure was refined by FSP at 350 revolutions per minute (RPM) tool rotation rate, while increasing the fraction of γ and decreasing the σ and ε content. The strength was further enhanced by FSP at 150 RPM by further refinement of the grain structure and increasing the fraction of ε phase. The peak ultimate tensile strength of ~1850 MPa was achieved by double pass FSP (350 RPM followed by 150 RPM), the sequence which even more refined the microstructure and increased the fraction of σ phase. While the content of diffusion created σ phase remains constant during subsequent compression, the fraction of ε increases due to the diffusionless strain induced γ→ε phase transformation. The transformation facilitates plastic strain accommodation and rapid strain hardening, which has been attributed to the increase in highly dislocated ε phase fraction and transformation induced dynamic Hall-Petch-type barrier effect. Interestingly, a great deal of hardening ability was exhibited by the HEA even at very high strength. Roles of texture, grain size, and phase content on the transformation during compression have been rationalized and discussed in this paper.

Effects of plasticity-induced martensitic transformation and grain refinement on the evolution of microstructure and mechanical properties of a metastable high entropy alloy

Deformation mechanism and microstructure evolution during superplastic deformation of friction stir processed CoCrFeNiMn high entropy alloy

Revealing the Effects of Friction Stir Processing on the Microstructural Evolutions and Mechanical Properties of As‐Cast Interstitial FeMnCoCrN High Entropy Alloy

Microstructure of and mechanical properties of an as-cast fine-grain dual-phase Fe-based high entropy alloy formed via solid-state phase transformation

Effect of aging temperature on microstructure and mechanical properties of Fe–Ni–Cr–Al high entropy alloy

Strength-ductility synergy of an additively manufactured metastable high-entropy alloy achieved by transformation-induced plasticity strengthening

Microstructure evolution and mechanical behavior of a CoCrFeNiMn0.75Cu0.25 high-entropy alloy by thermo-mechanical treatment

Modifying Transformation Pathways in High Entropy Alloys or Complex Concentrated Alloys Via Thermo-Mechanical Processing

Effect of Annealing on Microstructure Evolution and Tensile Behavior of Hot-Rolled FeMnCoCrAl High-Entropy Alloy

Toughening FeMn-based High-Entropy Alloys Via Retarding Phase Transformation

Mechanical behavior and microstructure-property correlation of a metastable interstitial high entropy alloy with hierarchical gradient structures

Effect of Multi-Pass Friction Stir Processing on Microstructure and Mechanical Properties of a Metastable Dual-Phase High Entropy Alloy

Work hardening behavior of hot-rolled metastable Fe50Co25Ni10Al5Ti5Mo5 medium-entropy alloy: in situ neutron diffraction analysis

Heterogeneous Microstructure and Tensile Properties of Fe50Mn30Co10Cr10 Metastable High-Entropy Alloy

Microstructure and Mechanical Property Evolution during Annealing of a Cold-Rolled Metastable Powder Metallurgy High Entropy Alloy

Microstructure Evolution and Mechanical Properties of AlCoCrFeNi2.1 Eutectic High-Entropy Alloys Processed by High-Pressure Torsion

Tunability of the Mechanical Properties of (Fe50mn27ni10cr13)100-Mo High-Entropy Alloys Via Secondary Phase Control

Plasticity Improvement in a Co-Rich Co<sub>40</sub>Fe<sub>25</sub>Cr<sub>20</sub>Ni<sub>15</sub> High-Entropy Alloy via Al Alloying

Tailoring Mechanical and Electrochemical Properties of the Cr15Fe20Co35Ni20Mo10 High-Entropy Alloy via the Competition between Recrystallization and Precipitation Processes

Plasticity Improvement in a Co-Rich Co40Fe25Cr20Ni15 High-Entropy Alloy via Al Alloying

Unexpected sluggish martensitic transformation in a strong and super-ductile high-entropy alloy of ultralow stacking fault energy