Abstract:In this research, the microstructure and micro mechanical property of linear friction welded joint for heteromorphic TC17 titanium alloy were investigated by nanoindentation testing and electron backscatter diffraction technique. The results show that the special microstructure in the weld zone (WZ) of the joint has great effects on its micro mechanical property. The WZ is composed of the transformed β phase, which exists in the form of equiaxed substructure, and the microstructure of the WZ can be divided into two parts along the centerline of the weld based on its main orientation. The WZ of the TC17 (α + β) side has the main orientation and , while the TC17 (β) side has the main orientation . Meanwhile, more high angle grain boundaries (HAGB) are found in the WZ of the TC17 (α + β) side. These microstructure characteristics have a significant impact on the micro mechanical property of the WZ. Due to more HAGB are in the WZ of the TC17 (α + β) side than the TC17 (β) side, the interface strengthening effect is a slightly stronger in the TC17 (α + β) side, which leads to better elastic modulus, hardness, and fracture toughness. While the TC17 (α + β) side microstructure has the and slip modes that are easier activated under RD direction force, so the microstructure in the WZ of the TC17 (α + β) side has a smaller yield strength and a larger hardening exponent than that in the WZ of the TC17 (β) side. In addition, it was also found that the area in the edge of the WZ near thermo-mechanically affected zone of the TC17 (α + β) side (TC17 (α + β)-TMAZ) has the minimum micro mechanical property and is the weak area of the WZ, which is related to the lower degree of recrystallization compared to other areas of the WZ. This area has the smallest elastic modulus (146.4 MPa), hardness (3.4 GPa), yield strength (904 MPa), and fracture toughness (0.173 MPa*m1/2), while the hardening exponent is 0.107. The macro tensile fracture location also matches the weak area in the WZ of the joints. Besides, it was also found that the average yield strength and tensile strength of the joint are 1016 MPa and 1065 MPa, while the elastic modulus and elongation are 111.2 GPa and 2.1%. And the microhardness distribution of the joint presents a "w" shape, which is due to lower phase α/β interface content in the WZ of the LFW joint for heteromorphic TC17 alloy and leads to the minimum mechanical property.

Effect of microstructure heterogeneity on the mechanical properties of friction stir welded reduced activation ferritic/martensitic steel

The Effect Of The Variation Of Microstructure In The Friction Stir Welded Zone On The Strain And Tensile Properties Of Al2139

Effect of Microstructure on High-Strength Low-Alloy Steel Welded Joint Toughness with Simulation of Heat-Affected Zone Coarse-Grained Area

Experimental and numerical studies of relationship between microstructures and mechanical properties in friction stir welding under water

Local inhomogeneity of mechanical properties in stir zone of friction stir welded AA1050 aluminum alloy

Effects of welding parameter on the microstructure and mechanical properties of friction stir-welded non-heat treatable alloy AA5083

Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Effect of Friction Time on Temperature Distribution, Plastic Flow, Microstructure, and Properties in Friction Welding of 1045 Carbon Steel and AISI 430 Ferritic Stainless Steel

Inter-relationship between microstructure evolution and mechanical properties in inertia friction welded 8630 low-alloy steel

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy

Microstructure and abnormal mechanical properties under the coupling effect of strain and temperature for friction-stir-welded joints of Al-Mg-Si alloy

Effect of layered heterogeneous microstructure design on the mechanical behavior of medium carbon steel

Effect of Friction Stir Welding and Tempering on the Microstructure and Strength of a Tempformed Low-Alloy Steel

Effect of welding speed on microstructure, nano-mechanical and nano-tribological characteristics of dissimilar friction stir welded AA6061-T6 and AZ31 alloy

Effect of Tool Speed on Microstructure Evolution and Mechanical Properties of Friction Stir Welded Joints of Al-Mg-Si Alloy with High Cu Content

Effects of microstrcture composition and orientation on micro mechanical properties of linear friction welding joint weld zone for heteromorphic TC17 titanium alloy

Microstructure evolution of thermo-mechanically affected zone in dissimilar AA2024/7075 joint produced by friction stir welding

Effect of Microstructure Evolution on Corrosion Behavior of Friction Stir Welded Joint for 2195-T8 Alloy

Behavior of microstructure and mechanical properties in the stir zone of friction stir welded ME21 magnesium alloy

Study on the materials flow, microstructure and mechanical properties of ultrasonic vibration-assisted friction stir weld of 1500 MPa martensitic steel

Effect of welding speed on microstructure and mechanical properties of Al−Mg−Mn−Zr−Tialloy sheet during friction stir welding