Abstract:To realize cost-effectively manufacture of high-performance Si3N4 porous ceramic, a ferrosilicon nitride porous ceramic with an optimized interlocking structure was synthesized by flash combustion synthesis using FeSi75 powder as raw material. And the technology has been improved in many ways to ensure stable industrial production. The theoretical combustion temperature of FeSi75 in N2(g) is up to 4608K, while Si3N4 is unstable. Both adding diluent and designing the preheat temperature of nitrogen are taken to control synthesis temperature below 1600 °C. During synthesis, the Fe–Si liquid phase and SiO(g), which are essential for the selective growth of elongated columnar β-Si3N4 and whisker α-Si3N4 respectively, are formed firstly. Then, nitriding proceed in multiple ways. N diffuses through Fe–Si(l) and reacts with Si to form β-Si3N4, and the growth of elongated β-Si3N4 in Fe–Si liquid follows the dynamic ripening model, which is very fast and effective. Thus, an interlocking structure composed of elongated β-Si3N4 with an aspect ratio above 20 is reached. There is also an indirect nitridation reaction, that is, FeSi75 preferentially reacts with trace O2 in atmosphere to form SiO(g), which is further nitrided to form needle-like α-Si3N4. Needle-like α-Si3N4 is interspersed in the well-developed columnar β-Si3N4, making the structure stronger. Fe finally exists in the form of Fe3Si, which binds the surrounding elongated Si3N4 to form a sea-urchin like unit, making the structure more stable and strengthened. Through control of these reactions, optimizations in microstructure are reached, and the annual output of has reached 25,000 tons. The reaction model is established.

Performance of silica bricks with ferrosilicon nitride as the mineralizer

New Route to Improve the Fracture Toughness and Flexural Strength of Si3N4 Ceramics by Adding FeSi2

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Evaluation of the morphology and pore characteristics of silica refractory using X-ray computed tomography

Effect of Silicon Addition on Mechanical Properties of Mullite-Sic Composite Refractories

Effect of MgF2 addition on mechanical properties and thermal conductivity of silicon nitride ceramics

Significant improvement of slag corrosion resistance and thermal shock resistance of corundum‐based dry vibratable refractory by addition of Fe–Si 3 N 4

A novel sintering additive system for porous mullite-bonded SiC ceramics: High mechanical performance with controllable pore structure

Cost-effective manufacture and synthesis mechanism of ferrosilicon nitride porous ceramic with interlocking structure

Phase Behavior of Silica Brick Used in Carbothermal Reduction

Improved water vapor corrosion resistance of SiC bricks via in situ formation of microporous Yb2Si2O7 bonding phase

Effect of Silicon Addition on High-Temperature Solid Particle Erosion-Wear Behaviour of Mullite-SiC Composite Refractories Prepared by Nitriding Reactive

In Situ Catalytic Synthesis of Si3N4 Nanowhiskers Reinforced SiC Refractories and Their High-Temperature Properties

Preparation and Properties of SiC Refractories Via Carbonization-Nitridation Reaction

Preparation and Mechanical Behavior of Si3N4 Composite Ceramics with Brick‐and‐mortar Structure

Simultaneous improvement in porosity and strength of porous β-Si3N4 ceramics by formation of ultrafine fibrous grains

Fabrication and Strengthening of Porous Si3N4 Ceramics by Replacement of Oxide Phase with Si3N4 at Grain Boundary Through Carbothermal Nitridation

Catalytic Preparation of Si3N4-Bonded SiC Refractories and Their High-Temperature Properties

Advanced Fabrication Method and Mechanical Properties of Silicon Nitride/Boron Nitride Fibrous Monolithic Ceramics

Fabrication of high performance silicon nitride ceramics with TiO2 additive by annealing process

Effect of Control Technology on Properties of Quartz Porous Brick