Abstract:So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoOx) to form a good contact. An a-Si:H(i)/MoOx stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al2O3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6" moly-poly cell, with an Al2O3/MoOx stack at the front side and n-type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al2O3 and MoOx layers, respectively. This resulted in an efficiency of 18.2% with a Voc of 651 mV, a FF of 75.6% and a Jsc of 36.9 mA/cm2. A post-deposition anneal (PDA) of the thin Al2O3 interlayer has significant effect on the Al2O3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher TPDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al2O3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.

Enhancing performance of heterojunction silicon solar cells through atomic-layer-deposited MoO x hole contact and atomic-layer-deposited AlZnO layer

Highly Efficient Silicon Heterojunction Solar Cells with ZnO:Al Transparent Electrode and Transition Metal Doped Indium Oxide Interfacial Layer

Atomic-Layer-Deposited H:MoO x Function Layer as Efficient Hole Selective Passivating Contact in Silicon Solar Cells

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

Aluminum and Molybdenum Co-Doped Zinc Oxide Films as Dual-Functional Carrier-Selective Contact for Silicon Solar Cells

Asymmetric TMO–Metal–TMO Structure for Enhanced Efficiency and Long-Term Stability of Si-Based Heterojunction Solar Cells

Crystalline Silicon Heterojunction Solar Cells with Metal Oxide Window Layers

MoOx Hole Collection Layer for A-Si: H Based Photovoltaic Cells

Performance analysis of c-Si heterojunction solar cell with passivated transition metal oxides carrier-selective contacts

Modulation of the TCO/MoO x Front Contact Enables >21% High-Efficiency Dopant-Free Silicon Solar Cells

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Simulation of High Efficiency Silicon Heterojunction Solar Cells with Molybdenum Oxide Carrier Selective Layer

Optimized Metallization for Interdigitated Back Contact Silicon Heterojunction Solar Cells

Interface Tuning through the MoO 3 Additive in Al Paste to Enhance the Performance of Crystalline Silicon Solar Cells

Heterojunction solar cells with asymmetrically carrier-selective contact structure of molybdenum-oxide/silicon/magnesium-oxide

Interface Tuning Through the MoO3 Additive in Al Paste to Enhance the Performance of Crystalline Silicon Solar Cells

Effective Hydrogenation Strategies to Boost Efficiency over 20% for Crystalline Silicon Solar Cell with Al2O3/Cu2O Passivating Contact

Nanocrystalline‐silicon hole contact layers enabling efficiency improvement of silicon heterojunction solar cells: Impact of nanostructure evolution on solar cell performance

Improved Performance of Titanium Oxide/Silicon Oxide Electron‐Selective Contacts by Implementation of Magnesium Interlayers

Molybdenum oxide hole selective transport layer by hot wire oxidation-sublimation deposition for silicon heterojunction solar cells

Tunable Hole Selective Transport by Solution‐processed MoO3‐x Via Doping for p‐Type Crystalline Silicon Solar Cells