Abstract:An investigation was conducted on the foaming formula and production technique of polyethylene terephthalate (PET) using orthogonal design analysis and Box–Behnken response surface analysis. PET was combined with polyolefin elastomer (POE) and filled with surface‐treated mica, quartz, and graphene oxide (GO). POE served as a carrier and modifier for the foaming agent, as well as a toughening agent. The addition of fillers can improve the thermal properties of PET foaming material. To do this, the blending process includes using a microsphere foaming agent on an open mill at a low temperature of 50°C for 5–6 min. After this, dicumyl peroxide (DCP) and antioxidant are added for 1 min before the specimens are removed from the open mill and flattened. The next step involves placing the specimens in a plate vulcanizing machine at 265°C and 10 MPa for 10 min to initiate the foaming process. The PET foam obtained has a density of 0.4–0.5 g/cm 3 , a tensile strength of 5–6.8 MPa, an elongation at break of 64–276%, and a tear strength of 5.1–14.5 N/m. Scanning electron microscope (SEM) images reveal that the PET foam contains micron‐sized cells, with measurements ranging from about 107 to 273 μm. The tested samples showed that the PET foam with 50 phr of POE, 7 phr of foaming agent, and 5 phr of mica exhibited relatively good mechanical properties, including tensile strength, elongation at break, and tear strength. The thermogravimetric analysis (TGA) indicated that the thermal properties of PET foam are better than those of pure PET. The modified PET foam has many applications due to its low density and excellent properties. This study introduces a new and uncomplicated method for producing PET foam, which differs from the commonly used extrusion foaming process that involves supercritical carbon dioxide or other media.

Fabrication of Lightweight Polyphenylene Oxide/High‐Impact Polystyrene Composite Bead Foam Parts via In‐Mold Foaming and Molding Technology

A Convenient and Efficient Path to Bead Foam Parts: Restricted Cell Growth and Simultaneous Inter-Bead Welding

Lightweight and High-Performance Polymethacrylimide Foams for Complex-Shaped Applications Based on the Highly Foamable Precursor Beads

In Situ Bead Fusion Induced by Elevated Foaming Temperatures and Compressive Forces During Constrained Bead Expansion

Polymer Bead Foams: A Review on Foam Preparation, Molding, and Interbead Bonding Mechanism

Fabrication of Lightweight Microcellular Polyimide Foams with Three-Dimensional Shape by Co2 Foaming and Compression Molding

Lightweight and High Impact Toughness PP/PET/POE Composite Foams Fabricated by In Situ Nanofibrillation and Microcellular Injection Molding

Lightweight and Strong Pp/Talc/Ptfe Foams with Enhanced Flame-Resistant Performance Fabricated by Microcellular Foam Injection Foaming

Poly(ether imide)/Epoxy Foam Composites with a Microcellular Structure and Ultralow Density: Bead Foam Fabrication, Compression Molding, Mechanical Properties, Thermal Stability, and Flame-Retardant Properties

Preparation and properties of polyimide/chopped carbon fiber composite foams

Lightweight and strong polypropylene/talc/polytetrafluoroethylene foams with enhanced flame-retardant performance fabricated by microcellular foam injection foaming

PS/PPO Foam with Excellent Comprehensive Properties Prepared by Integrated Foaming and Sintering Strategy with Microwave-assisted

Injection Molded Strong Polypropylene Composite Foam Reinforced with Rubber and Talc

Fabrication of Rigid Polyimide Foams with Overall Enhancement of Thermal and Mechanical Properties

Carbon nanotubes in microwave-assisted foaming and sinter molding of high performance polyetherimide bead foam products

Vitrimer bead foams: Cell density control by cell splitting in weld-compression molding

Fabrication of three-dimensional polyetherimide bead foams <i>via</i> supercritical CO<sub>2</sub>/ethanol co-foaming technology

High-strength, impact-resistant PP/PTFE composite foam with enhanced surface appearance achieved through mold-opening microcellular injection molding

Investigation on Foaming Ability of Modified Polyethylene Terephthalate (PET) Composites Prepared Using Compression Molding

Microcellular injection molded outstanding oleophilic and sound-insulating PP/PTFE nanocomposite foam

HDPE/UHMWPE Composite Foams Prepared by Compression Molding with Optimized Foaming Capacity and Mechanical Properties