Abstract:Deuterated polymer microspheres can be used as a neutron source in conjunction with lasers because thermonuclear fusion neutrons can be produced efficiently by collisions of the resulting energetic deuterium ions. A new type of solid deuterated polymer microsphere with a carbon hydrogen–carbon deuterium (CH-CD) multilayer has been designed for preparing the target for inertial confinement fusion (ICF) experiments. To fabricate these solid CH-CD multilayer microspheres, CH beads are first fabricated by a microfluidic technique, and the CD coating layer is prepared by a plasma polymerization method. Both polystyrene (PS) and poly(α-methylstyrene) (PAMS) are used as the material sources for the CH beads. The effects of the PS and PAMS materials on the quality of the solid CH beads and the resulting CH-CD multilayer polymer microspheres are investigated. The solid PS beads have better sphericity and a smoother surface, but large vacuoles are observed in solid PS-CD multilayer microspheres owing to the presence of residual fluorobenzene in the beads and a glass transition temperature of the solid PS beads that is lower than the temperature of plasma polymerization. Therefore, solid PAMS beads are more suitable as a mandrel for fabricating solid CH-CD multilayer polymer microspheres. Solid CH-CD multilayer microspheres with specified size have been successfully prepared by controlling the droplet size and the CD deposition rate and deposition time. Compared with the design value, the diameter deviation of the inner CH beads and the thickness deviation of the CD layer can be controlled within 20 µm and 2 µm, respectively. Thus, an approach has been developed to fabricate solid CH-CD multilayer microspheres that meet the physical design requirements for ICF.

Fabrication and Molding of Low Density Divinylbenzene Foams by ICF

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Model Optimization of Infrared Homogenization for Inertial Confinement Fusion Cryotargets

Topological Characteristics and Mechanical Properties of Uniaxially Thermoformed Auxetic Foam

Large Stiffness Thermoformed Open Cell Foams with Auxeticity

Inner Voids of Octavinyl Polyhedral Oligomeric Silsesquioxane Acting as Cell Embryos for Polymer Foaming

Fabrication of Lightweight Polyimide Foams with Exceptional Mechanical and Thermal Properties

Fabrication of Lightweight Polyphenylene Oxide/High‐Impact Polystyrene Composite Bead Foam Parts via In‐Mold Foaming and Molding Technology

Poly(ether imide)/Epoxy Foam Composites with a Microcellular Structure and Ultralow Density: Bead Foam Fabrication, Compression Molding, Mechanical Properties, Thermal Stability, and Flame-Retardant Properties

Fabrication of solid CH-CD multilayer microspheres for inertial confinement fusion

Preparation and Properties of High-Temperature-Resistant, Lightweight, Flexible Polyimide Foams with Different Diamine Structures

Boosting solubility performance of supercritical CO 2 via ethanol toward fabrication of polyetherimide/carbon fiber composite foam with three‐dimensional geometry shape

A Novel Vacuum-Assisted Method for Fabricating Flexible Polyimide Foams from 3,3′,4,4′-Oxydiphthalic Anhydride/4,4′-Oxydianiline

Dimensional Accuracy Control and Compressive Property of Microcellular Polyetherimide Honeycomb Foams Manufactured by an In Situ Foaming Fused Deposition Modeling Technology

Fabrication of Hydroxyl Modified Hollow Glass Microsphere Composite Isocyanate‐Based Polyimide Foam and Optimization Strategy Based on Different Bonding Mechanisms

Vitrimer bead foams: Cell density control by cell splitting in weld-compression molding

Fabrication of rigid polyimide foams via thermal foaming of nadimide-end-capped polyester-amine precursor

Hollow glass microspheres/phenolic syntactic foams with excellent mechanical and thermal insulate performance

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Fabrication of high porosity Nanocellular polymer foams based on PMMA/PVDF blends

Fabrication of Polyether–Ether–Ketone Foams with Superior Properties and Mitigated Weld Lines by Microcellular Injection Molding