Abstract:A facile manufacturing method to enable the in situ foam 3D printing of thermoplastic materials is reported. An expandable feedstock filament was first made by incorporation of thermally expandable microspheres (TEMs) in the filament during the extrusion process. The material formulation and extrusion process were designed such that TEM expansion was suppressed during filament fabrication. Polylactic acid (PLA) was used as a model material, and filaments containing 2.0 wt % triethyl citrate and 0.0-5.0 wt % TEM were fabricated. Expandable filaments were then fed into a material extrusion additive manufacturing process to enable the in situ foaming of microcellular structures during layer deposition. The mesostructure, cellular morphology, thermal behavior, and mechanical properties of the printed foams were investigated. Repeatable foam prints with highly uniform cellular structures were successfully achieved. The part density was reduced with an increase in the TEM content, with a maximum reduction of 50% at 5.0 wt % TEM content. It is also remarkable that the interbead gaps of mesostructure vanished due to the local polymer expansion during in situ foaming. The incorporation of TEM and plasticizer only slightly lowered the critical temperatures of PLA, that is, glass-transition, melting, and decomposition temperatures. Moreover, with the introduction of foaming, the specific tensile strength and modulus decreased, whereas the ductility and toughness increased severalfold. The results unveil the feasibility of a novel additive manufacturing technology that offers numerous opportunities toward the manufacturing of specially designed structures including functionally graded foams for a variety of applications.

Dimensional Accuracy Control and Compressive Property of Microcellular Polyetherimide Honeycomb Foams Manufactured by an In Situ Foaming Fused Deposition Modeling Technology

High-Strength and Shape-Memory Epoxy Cellular Material with Wood-Like Architecture

Fused deposition modeling of hierarchical porous polyetherimide assisted by an in-situ CO2 foaming technology

Enhanced interfacial adhesion and increased isotropy of 3D printed parts with microcellular structure fabricated via a micro‐extrusion CO2 foaming process

Poly(ether imide)/Epoxy Foam Composites with a Microcellular Structure and Ultralow Density: Bead Foam Fabrication, Compression Molding, Mechanical Properties, Thermal Stability, and Flame-Retardant Properties

Boosting solubility performance of supercritical CO 2 via ethanol toward fabrication of polyetherimide/carbon fiber composite foam with three‐dimensional geometry shape

Fabrication of Polyether–Ether–Ketone Foams with Superior Properties and Mitigated Weld Lines by Microcellular Injection Molding

In Situ Foam 3D Printing of Microcellular Structures Using Material Extrusion Additive Manufacturing.

Acoustic-assisted DLP 3D Printing Process for Carbon Nanofiber Reinforced Honeycomb Structures

Construction of Bionic Porous Polyetherimide Structure by an In Situ Foaming Fused Deposition Modeling Process

Microcellular injection molding of foamed engineering plastic parts with high dimensional accuracy

Super‐Elastic and Dimensionally Stable Polyether Block Amide Foams Fabricated by Microcellular Foaming with CO2&N2 as Co‐Blowing Agents

Fabrication of a novel continuous fiber 3D printed thermoset all-composite honeycomb sandwich structure with polymethacrylimide foam reinforcement

Fabrication of Lightweight Polyphenylene Oxide/High‐Impact Polystyrene Composite Bead Foam Parts via In‐Mold Foaming and Molding Technology

Selective coaxial ink 3D printing for single-pass fabrication of smart elastomeric foam with embedded stretchable sensor

Hierarchical cellular scaffolds fabricated via direct foam writing using gelled colloidal particle‐stabilized foams as the ink

A new modelling method for open cell foam structure based on centroidal and capacity constraint power diagram

Effect of Absorbent Foam Filling on Mechanical Behaviors of 3D-Printed Honeycombs

Interfacial performance and build orientation of 3D‐printed poly(ether‐ketone‐ketone) reinforced by continuous carbon fiber

Fabrication of lightweight polyethersulfone foams with enhanced surface quality and high specific flexural properties using micro‐opening microcellular injection molding

Real-microcellular poly(ether-block-amide)/carbon fiber foams with improved mechanical property and surface quality for high-performance electromagnetic interference shielding applications