Abstract:Polymers reinforced with conducting fibers to achieve electrical conductivity have attracted remarkable attention in several engineering applications, and injection molding provides a cost-effective way for mass production. However, the electrical performance usually varies with the molding conditions. Moreover, high added content of conducting fibers usually results in molding difficulties. In this study, we propose using microcellular (MuCell) injection molding for polypropylene (PP)/carbon fiber (CF, 20, and 30 wt%) composites and hope that the MuCell injection molding process can improve both electrical and mechanical performance as compared with conventional injection molded (CIM) parts under the same CF content. Both molding techniques were also employed with and without gas counter pressure (GCP), and the overall fiber orientation, through-plane electrical conductivity (TPEC), and tensile strength (TS) of the composites were characterized. Based on the various processing technologies, the results can be described in four aspects: (1) Compared with CIM, microcellular foaming significantly influenced the fiber orientation, and the TPECs of the samples with 20 and 30 wt% CF were 18-78 and 5-8 times higher than those of the corresponding samples molded by CIM, respectively; (2) when GCP was employed in the CIM process, the TPEC of the samples with 20 and 30 wt% CF increased by 3 and 2 times, respectively. Similar results were obtained in the case of microcellular injection molding-the TPEC of the 20 and 30 wt% composites increased by 7-74 and 18-32 times, respectively; (3) although microcellular injection molding alone (i.e., without GCP) showed the greatest influence on the randomness of the fiber orientation and the TPEC, the TS of the samples was the lowest due to the uncontrollable foaming cell size and cell size uniformity; (4) in contrast, when GCP was employed in the microcellular foaming process, high TS was obtained, and the TPEC was significantly enhanced. The high foaming quality owing to the GCP implementation improved the randomness of fiber orientation, as well as the electrical and mechanical properties of the composites. Generally speaking, microcellular injection combined with gas counter pressure does provide a promising way to achieve high electrical and mechanical performance for carbon-fiber-added polypropylene composites.

High-strength, impact-resistant PP/PTFE composite foam with enhanced surface appearance achieved through mold-opening microcellular injection molding

Microcellular injection molded outstanding oleophilic and sound-insulating PP/PTFE nanocomposite foam

Lightweight and Strong Pp/Talc/Ptfe Foams with Enhanced Flame-Resistant Performance Fabricated by Microcellular Foam Injection Foaming

Lightweight and High Impact Toughness PP/PET/POE Composite Foams Fabricated by In Situ Nanofibrillation and Microcellular Injection Molding

Tough and Defect-Free-surfaces PA66/PTFE Composite Foam with Bimodal Structure Achieved by High-Pressure Foam Injection Molding with Mold-Opening

Mold-opening foam injection molded strong PP/CF foams with high EMI shielding performance

Lightweight and strong polypropylene/talc/polytetrafluoroethylene foams with enhanced flame-retardant performance fabricated by microcellular foam injection foaming

Development of High Thermal Insulation and Compressive Strength BPP Foams Using Mold-Opening Foam Injection Molding with In-Situ Fibrillated PTFE Fibers

Effect of Mold Opening on Microcellular Polyether-Ether-ketone Fabricated by Injection Molding

Cell Morphology And Mechanical Properties Of Microcellular Mucell (R) Injection Molded Polyetherimide And Polyetherimide/Fillers Composite Foams

High Thermal Insulation and Compressive Strength Polypropylene Foams Fabricated by High-Pressure Foam Injection Molding and Mold Opening of Nano-Fibrillar Composites

Processing Effects on the Through-Plane Electrical Conductivities and Tensile Strengths of Microcellular-Injection-Molded Polypropylene Composites with Carbon Fibers

Effects of Process Conditions and Nano-Fillers on the Cell Structure and Mechanical Properties of Co-Injection Molded Polypropylene-Polyethylene Composites

The Cellular Structure and Mechanical Properties of Polypropylene/Nano-CaCO3/Ethylene-propylene-diene-monomer Composites Prepared by an In-Mold-Decoration/Microcellular-Injection-Molding Process

Fabrication of lightweight polyethersulfone foams with enhanced surface quality and high specific flexural properties using micro‐opening microcellular injection molding

Crystallinity and mechanical properties of polypropylene products foamed by microcellular injection molding process

Lightweight and High-Performance Polymethacrylimide Foams for Complex-Shaped Applications Based on the Highly Foamable Precursor Beads

Morphology and Properties of Injection Molded Microcellular Poly(Ether Imide) (pei)/polypropylene (pp) Foams

Effect of inorganic nanoparticles on polypropylene in‐mold decoration and microcellular foaming injection molding composites

Preparation and characterization of microcellular injection molded foams from high-performance blends based on PPS-modified PPBESK

Foaming Behaviors of Polyetherimide/ Polypropylene-Graft-Maleic Anhydride Blends in the Microcellular Injection Molding Process