Abstract:Multi-layer crystallization and uncontrollable defects were the main factors that limiting the quality of Cu 2 ZnSn(S,Se) 4 (CZTSSe) films. Here a hybrid crystallization strategy was proposed to simultaneously improve the morphology and defect properties of CZTSSe film. Firstly, we found the variation of the microstructures (constitution, chemical environment of the elements, etc.) in precursor films can greatly alter the grain-growths of CZTSSe films. Detailed characterizations revealed that the chemical environment of S in the precursor film may influence the S-to-Se substitution of the film during the selenization process. This can further affect the grain-growth mechanism and the properties of CZTSSe film. While the S-to-Se substitution of the film mainly occurred below 500°C, the NaSe x on the surface of the film could dominate the grain-growth (Na-mechanism). For this mechanism, the CZTSSe film exhibited bi-layer morphology and relatively high band-tail energy, but shallow-acceptor was detected in the film. The solar cells based on the CZTSSe films reached the efficiency of 10.6%. As a comparison, liquid phase could be generated when the S-to-Se substitution of the film shifted to higher temperature (>500°C). In this condition, the grain-growth would be dominated by the liquid phase (LP-mechanism). Such mechanism can eliminate the multi-layer crystallization and reduce the band-tail energy, but the surface properties of the CZTSSe film was deteriorated and the formation of shallow-acceptor in CZTSSe was inhibited. The fabricated solar cells achieved the efficiency of 10.3%. Based on the results above, a bi-layer precursor film contained sub-layers with different microstructures was proposed to regulate the crystallization of CZTSSe. The co-existence of different microstructures in the precursor film could induce a hybrid grain-growth mechanism for the CZTSSe film (e.g., the Na-mechanism worked on the surface while the LP-mechanism worked in the bottom simultaneously). Such grain-growth mechanism can yield CZTSSe film with uniform morphology and favorable defect properties. The CZTSSe solar cells based on the hybrid grain-growth mechanism achieved the best efficiency of 12.6%. The investigation in this paper would provide new solutions for the crystallization regulation on CZTSSe photovoltaic material.

Effects of the growth process on surface morphology of Cu2(Sn1−xGex)S3 thin films

Fabrication of Cu2Sn1-xGexS3 Thin-Film Solar Cells via Sulfurization of Cu2GeS3/Cu2SnS3 Stacked Precursors

Phase composition of the earth-abundant Cu2SnS3 thin films with different annealing temperature and its effects on the performance of the related solar cells

Effect of the stacking order, annealing temperature and atmosphere on crystal phase and optical properties of Cu2SnS3

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se 2 Films by (NH 4 ) 2 S Solution at Room Temperature

Effect of Ge content on diode parameters of superstrate type Cu2ZnSn1−xGexS4/CdS heterostructures prepared by all-solution process

Investigation of Cu(In,Ga)Se2 Polycrystalline Growth: Ga Diffusion and Surface Morphology Evolution

Fabrication of Cu2SnS3 Thin Film Solar Cells Via a Sol-Gel Technique in Air

Effect of Sulfurization Temperature on Properties of Cu2ZnSnS4 Thin Films and Diffusion of Ti Substrate Elements

Direct vapour transport grown Cu2SnS3 crystals: exploring structural, elastic, optical, and electronic properties

Grain growth of CZTSSe via nanocrystal selenization

Improving the efficiency of Cu2ZnSnS4 solar cells by promoting the homogeneous distribution of Sn element

Modification of surface and interface of copper indium gallium selenide films with sulfurization

Synthesis, Growth and Characterization of Cu2CoSnS4 Thin Films via Thermal Evaporation Method

Growth and Characterization of Copper Indium Gallium Diselenide Films for Solar Cells Fabrication

Impact of Sulfuration Time on Properties of CuInS2 Films

Pulsed rapid thermal process for tailoring the surface sulfurization of CIGSe thin film at low temperature

Simultaneously improving the morphology and defect properties of CZTSSe film via hybrid grain-growth mechanism

Growth Mechanism and Properties of Nanostructure Cu 2 ZnSnSe 4 Thin Films and Solar Cells

Preparation of High-Quality Cu2ZnSnS4 Thin Films for Solar Cells Via the Improvement of Sulfur Partial Pressure Using a Static Annealing Sulfurization Approach

Optimization of CuInGaSSe properties and CuInGaSSe/CdS interface quality for efficient solar cells processed with CuInGa precursors