Abstract:In this study, the addition of the rare earth oxide CeO2 was investigated to alter the microstructural properties of the nano-WC-reinforced Ni-based composite coatings. The reinforced composite was prepared on the 42CrMo steel surface using a semiconductor laser. The morphology and microstructure of coatings were analyzed using a scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). Further, the digital microhardness tester and high-temperature friction and wear tester were used to observe the mechanical properties. The results indicated that the addition of CeO2 eliminated the cracks from the surface of the coatings and effectively reduced the number of pores. The phases were mainly observed as γ-Ni(Fe) in a solid solution, and some residual WC and W2C phases were observed. In addition, Fe3C, Cr23C6, M6C (M = W, Fe, and Ni), SiC and Cr7C3 composite carbides, Si2W and NiW tungsten compounds, and CeFe2- and CeNi2-containing Ce complex compounds were formed on the coating. The rare earth oxide CeO2 composite-modified coating mainly comprised dendrites, crystal cells, strips, and massive microstructures. The reinforced phases of the modified coating presented uniform dispersion distribution with the addition of 1% CeO2, and the structures were significantly refined. The maximum microhardness of the modified coating was approximately 1560 HV0.2, which was approximately 20% higher than that of the unmodified composite coating. The minimum wear loss of the modified coating was 6.1 mg and the minimum frictional coefficient was approximately 0.23, which were better than those of the unmodified coating. The wear mechanism of the nano-WC-reinforced Ni-based coating was primarily adhesive, whereas that of the CeO2 composite modified coating was mainly abrasive particle wear, which accompanied adhesive wear.

Effects of micro/nano CeO2 on the microstructure and properties of WC-10Co cemented carbides

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Effect of Cu and CeO2 additives on structure and performance of WC-10Co cemented carbides

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effects of nanocomposite grain growth inhibitors and multi-walled carbon nanotubes on the microstructure and mechanical properties of ultrafine cemented carbides

Effects of Cr3C2, VC, and TaC on Microstructure, WC Morphology and Mechanical Properties of Ultrafine WC–10 wt. % Co Cemented Carbides

Effect of the Rare Earth Oxide CeO2 on the Microstructure and Properties of the Nano-WC-Reinforced Ni-Based Composite Coating

Microstructure and properties of ultrafine WC–Co–VC cemented carbides with different Co contents

Effect of particle size and high-energy ball milling time on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Synthesis of Y2O3-doped WC-Co powders by wet chemical method and its effect on the properties of WC-Co cemented carbide alloy

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

Enhanced Coarse-Grained WC-Co(Ce) Cemented Carbide Prepared through Co-Precipitation

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

Effects of nano-alumina on mechanical properties and wear resistance of WC-8Co cemented carbide by spark plasma sintering

Effect of CeO2 Content on Microstructure and Properties of SiCp/Al-Si Composites Prepared by Powder Metallurgy

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives

Effect of MWCNTs on microstructure and properties of WC-9Co gradient cemented carbides

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effect of Y2O3 on microstructure and mechanical properties of WC-Co-cemented carbides prepared via solid-liquid doping method and spark plasma sintering

Effect of Nano-AlN Addition on the Microstructure and Mechanical Properties of Binderless WC-VC-TaC-AlN Cemented Carbides