Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Microstructure and Tribological Performances of W-Cu-Co-xWC Alloys with Various WC Amounts

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Microstructural characteristics and wear-resistant mechanisms of WC-TiC-co coatings with varying TiC contents

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Microstructure and Tribological Properties of WC/Ni-MoS2 Titanium-Based Composite Coating on TC4

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Tribological and Electrochemical Corrosion Behaviors of Cu-based Powder Metallurgy Composites Reinforced by In-Situ WC with Different Morphology

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Enhanced Mechanical and Electrical Properties of CuCrZr-WC Alloy Prepared by Mechanical Alloying and Spark Plasma Sintering

Effect of WC addition on microstructure and properties of laser melting deposited Ti6Al4V

Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives

Effects of WC mass fraction on microstructure and tribological behavior of plasma sprayed FeMnCoCr–WC coatings

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Microstructure evolution and tribological behavior of laser cladded Al 1.8 CrCuFeNi 2 /WC composite coatings on Ti-6Al-4 V

Investigations on the microstructures and tribological behaviors of as-cast CrFeCoNiCu x high entropy alloys

Dry sliding wear behavior of additively manufactured CoCrWNixAly alloys

Effect of WC addition on microstructure and properties of powder metallurgy CoCrNi medium entropy alloy

Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Effect of Y2O3 on microstructure and mechanical properties of WC-Co-cemented carbides prepared via solid-liquid doping method and spark plasma sintering