Abstract:Selective Laser Melting (SLM), as an emerging additive manufacturing technology, has attracted increasing attention in the field of copper alloys. To reduce the production cost of SLM-formed copper alloys and enhance the mechanical properties of the alloy materials, this work uses CuSn10 alloy powder prepared by the water atomization method as the raw material, and optimizes the process parameters during SLM through the response surface and variance analysis methods, to prepare almost fully dense CuSn10 alloy blocks. By adding a certain proportion of WC hard particles to the CuSn10 alloy powder, this work investigates the microstructural evolution and mechanical properties of the specimens before and after the addition of particles, and explores the regularity of the influence of the addition of hard particles on the microstructural evolution and mechanical properties of the formed parts by comparing the experimental results. The results show that the SLM-formed CuSn10 specimens exhibit a fine-grained microstructure composed of cellular and dendritic structures. The addition of WC hard particles changes the microstructure of the composite material, eliminating the preferred growth inside the specimens, and due to the effects of hard carbide phase, heterogeneous nucleation and dispersion strengthening, a more refined and uniform microstructure is achieved. The performance of the specimens also varies considerably, with the Vickers hardness increasing from 155HV to 215HV, the ultimate tensile strength increasing from 578MPa to 625MPa, and the elongation at fracture decreasing from 15% to 5%. The wear resistance and corrosion resistance show the same trend, with the wear resistance and corrosion resistance of the composite material first decreasing and then increasing as the WC content increases, reaching the best when the content is 10%. It can be seen that by reasonably adjusting the proportion of the WC reinforcement phase in the copper-based composite material, the hardness and wear resistance of the SLM-formed CuSn10 alloy can be significantly improved, expanding the engineering application prospects of copper alloy parts in extreme working conditions such as wear and corrosion.

Enhanced Mechanical and Electrical Properties of CuCrZr-WC Alloy Prepared by Mechanical Alloying and Spark Plasma Sintering

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Effect of alloying element Zr on microstructure and properties of Cu−Y2O3 composites

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Effect of WC addition on microstructure and properties of powder metallurgy CoCrNi medium entropy alloy

Fabrication and characterization of W/Cu/Ni-based high specific gravity alloy with Zr and Ti combined addition

Effects of WC Particles on the Microstructure and Properties of Copper Matrix Composites by Selective Laser Melting

Optimizing mechanical and electrical properties of Cu–3Zr alloy by thermomechanical processing

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Study on Microstructure and Properties of Cu-Zr Alloy Prepared by Mechanical Alloying

Tribological and Electrochemical Corrosion Behaviors of Cu-based Powder Metallurgy Composites Reinforced by In-Situ WC with Different Morphology

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

Additive Manufacturing of High-Strength CrMnFeCoNi High-Entropy Alloys-Based Composites with WC Addition

Study on Microstructure and Properties of WC Particle-Reinforced FeCoCrNi-Matrix High Entropy Alloy Composites

Realizing the combination of high strength and good ductility of Cu matrix composites with CrCoNi reinforcement particles and microlaminated structure

Effect of Metal Elements on Microstructure and Mechanical Properties of Ultrafine Cemented Carbide Prepared by SPS

Sc/Zr microalloying on strength-corrosion performance synergy of wire-arc directed energy deposited Al-Mg

Microstructure, mechanical properties, and wear behavior of AlCoCrFeNi high-entropy alloy and AlCrFeNi medium-entropy alloy with WC addition