Abstract:To surpass the current level of mechanical properties exhibited by CoCrNi medium-entropy alloys (MEA), (CoCrNi) 100−x (WC) x (x = 0, 2, 4 and 6 for molar ratio) MEA samples were prepared using powder metallurgy with atomized powder as the raw material, and the influence of WC content on the microstructural evolution and mechanical properties of the sintered MEAs was investigated. As the WC content increased, the phase structure of the sintered MEAs changed from a single FCC phase to an FCC+Cr 23 C 6 phase, while the grain size of the matrix decreased. Consequently, the strength of the alloy exhibited significant improvement. For instance, the tensile yield and fracture strengths of (CoCrNi) 98 (WC) 2 were measured at 574 and 971 MPa, respectively, while maintaining a plasticity of approximately 41.6%. Furthermore, the addition of WC led to a considerable increase in the hardness for (CoCrNi) 94 (WC) 6 , reaching 314.7 HV, which was nearly 50% higher than that of the CoCrNi matrix. The increased hardness proved beneficial in enhancing the material's wear resistance, which first increased and then decreased. The wear mechanisms primarily involved abrasive and oxidation wears. The observed increase in yield strength can be attributed to the combined effects of multiple strengthening mechanisms. The individual contributions of these mechanisms were quantitatively evaluated and compared to the actual values, demonstrating consistency with the calculated results. Notably, solid-solution strengthening emerged as the principle strengthening mechanism.

Additive Manufacturing of High-Strength CrMnFeCoNi High-Entropy Alloys-Based Composites with WC Addition

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Additive Manufacturing of High-Strength CrMnFeCoNi-based High Entropy Alloys with TiC Addition

Influence of in-situ and ex-situ precipitations on microstructure and mechanical properties of additive manufacturing CoCrFeMnNi high-entropy alloys

Superior Strength-Ductility Synergy in Additively Manufactured CoCrFeNi High-Entropy Alloys with Multi-Scale Hierarchical Microstructure

Ultra-high strength of additively manufactured CoCrNi medium entropy alloy with high-fraction TiC

Effect of WC addition on microstructure and properties of powder metallurgy CoCrNi medium entropy alloy

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

In situ strengthening of CrMnFeCoNi high-entropy alloy with Al realized by laser additive manufacturing

In-situ synthesis of Alx-Co-Cr-Ni high entropy alloys via twin-wire and arc additive manufacturing (T-WAAM): microstructure evolution and mechanical properties

Enhancing tensile properties of laser additive manufactured FeCoNiCrMn high entropy alloy via adding Fe-based metallic glass

Strengthening FeCrNiCu high entropy alloys via combining V additions with in-situ TiC particles

Microstructure evolution and mechanical properties of Al CoCrFeNi high-entropy alloys by laser melting deposition

Corrosion Resistance Enhancement of CoCrFeMnNi High-Entropy Alloy with WC Particle Reinforcements via Laser Melting Deposition

Synergistic strengthening of FeCrNiCo high entropy alloys via micro-TiC and nano-SiC particles

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

Introduction of nanoprecipitation into supersaturated CoCrFeNiMo0.5 alloy prepared by laser-powder bed fusion via microstructure tailoring to achieve excellent properties

Microstructure evolution and high temperature wear resistance of in-situ synthesized carbides reinforced NiCoFeCrSiMo high entropy alloy coatings fabricated by laser cladding

In-situ synthesis of CoCrFeMnNi high-entropy alloy by selective laser melting

Effect of Si and C additions on the reaction mechanism and mechanical properties of FeCrNiCu high entropy alloy