Abstract:It has recently been shown that solid-state nanometer-scale pores ('nanopores') can be used as highly sensitive single-molecule sensors. For example, electrophoretic translocation of DNA, RNA and proteins through such nanopores has enabled both detection and structural analysis of these complex biomolecules. Control over the nanopore size is critical as the pore must be comparable in size to the analyte molecule in question. The most widely used fabrication methods are based on focused electron or ion beams and thus require (scanning) transmission electron microscopy and focused ion beam (FIB) instrumentation. Even though very small pores have been made using these approaches, several issues remain. These include the requirement of being restricted to rather thin, mechanically less stable membranes, particularly for pore diameters in the single-digit nanometer range, lack of control of the surface properties at and inside the nanopore, and finally, the fabrication cost. In the proof-of-concept study, we report on a novel and simple route for fabricating metal nanopores with apparent diameters below 20 nm using electrodeposition and real-time ionic current feedback in solution. This fabrication approach inserts considerable flexibility into the kinds of platforms that can be used and the nanopore membrane material. Starting from much larger pores, which are straightforward to make using FIB or other semiconductor fabrication methods, we electrodeposit Pt at the nanopore interface while monitoring its ionic conductance at the same time in a bi-potentiostatic setup. Due to the deposition of Pt, the nanopore decreases in size, resulting in a decrease of the pore conductance. Once a desired pore conductance has been reached, the electrodeposition process is stopped by switching the potential of the membrane electrode and the fabrication process is complete. Furthermore, we demonstrate that these pores can be used for single-biomolecule analysis, such as that of λ-DNA, which we use in a proof-of-concept study. Importantly, our approach is applicable to single nanopores as well as nanopore arrays, and can easily be extended to deposits of metal other than Pt.

Wafer-Scale Fabrication of Uniform, Micrometer-Sized, Triangular Membranes on Sapphire for High-Speed Protein Sensing in a Nanopore

Sapphire-supported nanopores for low-noise DNA sensing

Monolithic Integration of Vertical Thin-Film Transistors in Nanopores for Charge Sensing of Single Biomolecules

Fabrication of Sub-Nanometer Pores on Graphene Membrane for Ion Selective Transport

Fabrication of Solid State Nanopore in Thin Silicon Membrane Using Low Cost Multistep Chemical Etching

Monolithic Fabrication of NPN/SiNx Dual Membrane Cavity for Nanopore-based DNA Sensing

Fabrication of Sub-20 Nm Nanopore Arrays in Membranes with Embedded Metal Electrodes at Wafer Scales

Nanopore arrays in a silicon membrane for parallel single-molecule detection: fabrication

Photothermally Assisted Thinning of Silicon Nitride Membranes for Ultrathin Asymmetric Nanopores.

Scaled‐up Synthesis of Freestanding Molybdenum Disulfide Membranes for Nanopore Sensing

A Method for Fabricating CMOS Back-End-of-Line-Compatible Solid-State Nanopore Devices

Fabrication of Hourglass-Shaped Solid-State Nanopores

Precise electrochemical fabrication of sub-20 nm solid-state nanopores for single-molecule biosensing

Ultra-Thin, High-Lifetime Silicon Nitride Membranes for Nanopore Sensing

Localized nanopore fabrication in silicon nitride membranes by femtosecond laser exposure and subsequent controlled breakdown.

Muitilpe Nanopores Fabrication in a SiNX Membrane Via Controlled Breakdown

Through-membrane electron-beam lithography for ultrathin membrane applications

Instant Formation of Nanopores on Flexible Polymer Membranes Using Intense Pulsed Light and Nanoparticle Templates

Fabrication of solid-state nanopores

Rapid fabrication of solid-state nanopores with high reproducibility over a large area using a helium ion microscope.

Fabricatable Nanopore Sensors with an Atomic Thickness