Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Microstructure and Electrochemical Properties for WC/a-C Coatings As ECG Dry Bioelectrodes

Microstructure and Corrosion Behaviour of WC-Co Coating Fabricated by Plasma Arc Welding

Characterization of Dry Biopotential Electrodes

Microstructure and electrochemical properties of Cr– Si–C–N coatings as biological dry electrode

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Microstructure and Electrochemical Characterization of Ti–Al–C–N Coatings As Biological Dry Electrodes

Electrochemical and Structural Characterization of Nanocomposite CrSiCN Coatings for Biological Dry Electrodes

Surface morphology and crystal orientation of electrodeposited tungsten coatings with different pulse parameters

Robust Ni/WC superhydrophobic surfaces by electrodeposition

Electrodeposition of Ni-WC composite coatings: formation, structure and properties

Properties of Al/conductive coating/ α -PbO 2 -CeO 2 -TiO 2 / β -PbO 2 -WC-ZrO 2 composite anode for zinc electrowinning

In Vivo Electrochemical Analysis of a PEDOT/MWCNT Neural Electrode Coating

Properties of Al/conductive coating/α-PbO2-CeO2-TiO2/β-PbO2-WC-ZrO2 composite anode for zinc electrowinning

Improved electrochemical performances of lithium–oxygen batteries with tungsten carbide-coated cathode

Fructus Xanthii-Inspired Low Dynamic Noise Dry Bioelectrodes for Surface Monitoring of ECG

Effects of Current Density on Preparation and Performance of Al/conductive Coating/a-Pbo2-ceo2-tio2/ß-pbo2-mno2-wc-zro2 Composite Electrode Materials

Rapid Fabrication Technique for Dry Electrocardiography Electrodes Using Carbon Nanotube/Polydimethylsiloxane Composite

Comparison of Corrosion Behavior of a-C Coatings Deposited by Cathode Vacuum Arc and Filter Cathode Vacuum Arc Techniques

Preparation of WC x Thin Films by RF Sputtering and Their Electrocatalytic Property for Anodic Methanol Oxidation

Electrospun Rubber Nanofiber Web-Based Dry Electrodes for Biopotential Monitoring

Electrochemical corrosion behavior variation of WC-10Co4Cr coating subjected to different magnetic treatments and its mechanism