Introduction to Ultra-Supercritical Boiler Blowpipe Program

Wei Yang

2010-01-01

Abstract:It is necessary to clean the main steam pipe,reheating steam pipe for a new power plant.For this purpose,the high velocity steam is introduced to the pipes,tubes and exhausted to remove and blow off the particle or other foreign materials in the tubes or pipe in order to guarantee the security of steam turbine.

What problem does this paper attempt to address?

Technical Study on Three-Staged Pipe-Blowing Method Used in Double Reheat Unit

Lin WANG,Hui LIU,Chao LIU,Jinghui GAO,Zhidan ZHAO,Hongyv WANG,Yingqi MENG

DOI: https://doi.org/10.11930/j.issn.1004-9649.2017.07.069.05

2017-01-01

Abstract:Due to the higher thermal efficiency and the lower pollutant emissions,the double-reheat cycle technology is getting moreapplied in the industry..Therefore,the steam blowing process for the new units with double-reheat cycle calls for urgent study.In this paper,an ultra-supercritical 660 MW double-reheat boiler is taken as the study object.Based on the routine one-staged and two-staged pipe-blowing techniques,the three-staged pipe-blowing with pressure-reduction steam is proposed in accordance with the arrangement of the boiler heating surfaces.The results of the target plate test show that the number of the flushed spots are less than 5 and the diameters of the spots are all smaller than 0.5 mm,which completely meets the requirements of the national codes.The three-staged pressure-reduction pipe-blowing method,which produces good blowing quality,can provide practical reference for subsequent units with double reheat technology.
Practice and optimization of combined pipe-blowing method for domestic first double-reheat unit

Jinghui GAO,Lin WANG,Bo YANG,Yafu ZHANG,Zhidan ZHAO,Hongyu WANG,Yingqi MENG

DOI: https://doi.org/10.3969/j.issn.1002-3364.2017.08.107

2017-01-01

Abstract:To explore suitable pipe-blowing methods for ultra supercritical double-reheat units, a decompression combined pipe-blowing method was proposed and put into practice on the domestic first double-reheat boiler. This new method is a combination of "one section pipe-blowing" method's structure and "two-section pipe-blowing" method's operating characteristics. The superheater, primary reheater, secondary reheater and its associated pipelines were connected in series in one time. The whole system is divided into three parts, and each part is purged and targeted separately. For the problem that the steam purge coefficient does not satisfy the standard, field test and theoretical analysis were carried out. Some measures, such as increasing the separator outlet steam pressure, opening multiple valves simultaneously, were taken into practice to eliminate the blocking flow effect and guarantee the purging quality. The final target plate tests results show that, the depression combined pipe-blowing method completed the purging of double-reheat boiler heating surfaces with high quality. This method can provide practical reference for other similar units.
Automatic Welding System Design for Connecting Piece of Heating Surface Piping of Ultra Supercritical Boiler

LIU Jun,YANG Hui-qin,WANG Ye,SHI Zhen

DOI: https://doi.org/10.3969/j.issn.1001-3997.2012.03.060

2012-01-01

Abstract:Ultra supercritical boiler is the future development direction of thermal power units.In the piping system of ultra supercritical boiler heating surface,due to the structure layout and other reasons,a large amount of connecting pieces must be used and SMAW technology be applied at present,whose manufacturing precision is not high, product quality is unstable and production efficiency is low.According to their welding technical requirements and regularity of distribution,a Longmen type mechanical structure of gas shielded welding robot is designed,which power for automatic welding adopts IGBT inverter DC control pulse of DP400 digital of OTC to construct PLC system based on touch screen.This system can realize the multi-combination of welding parameters setting and welding parameter match optimizing.
Analysis on the Steam Temperature Deviation of the Vertical Water Wall and the Adjustment Plan of the Throttle Ring for an Ultra-supercritical Boiler

YANG Haoyu,ZHANG Xirong,LI Weiteng,YANG Dong,WANG Yongjie,SONG Baojun,XIA Liangwei

DOI: https://doi.org/10.19805/j.cnki.jcspe.2023.05.003

2023-01-01

Abstract:Experimental research and hydrodynamic calculation were carried out to solve the problems of deviation in steam temperature, large temperature fluctuation and the transverse cracks in the lower furnace water wall of a 660 MW ultra-supercritical boiler. According to the boiler design scheme, a hydrodynamic calculation mathematical model for the boiler flow network system was established, and the temperature test points were arranged on the water wall. Based on the actual furnace measurement data of the steam temperature, the heat load and thermal deviation distribution in the unit 1 furnace at 270 MW load was calculated. Then the arrangement of the throttle ring was adjusted, and the adjusted hydrodynamic and flow instability was calculated. Results show that the outlet steam temperature is more uniform and the adjustment can prevent steam temperature fluctuation without pulsation. At the same time, the steam temperature distribution of the lower furnace water wall at medium and high loads is more uniform after the throttle ring adjustment, and the temperature deviation is significantly improved.
Application study on enamel heat exchange tube in GGH of coal-fired units with ultra-low flue gas emission

Quanbin ZHANG,Jianguo YANG

DOI: https://doi.org/10.3969/j.issn.1002-3364.2017.09.130

2017-01-01

Abstract:The water medium heat pipe gas-gas heater (MGGH) is an important part of ultra-low flue gas emission technology for coal-fired boilers, of which the operating environment is bad and the corrosion mechanism of the heat exchange tube is complex, it is a key problem to solve the low temperature corrosion of heat exchange tube.Analysis on corrosive mechanism of the heat exchange tube shows that the low temperature section of the gas reheater in the MGGH is located on the No.II serious corrosion zone. There are two engineering techniques to control the low temperature corrosion rate and the heat exchanger tube materials of 316L, DIN1.4529, plastic and enamel can satisfy the requirement. It finds that the enamel heat exchange tube can meet the engineering requirements through the research and comparison. From several aspects such as the corrosion resistance of sulfuric acid, thermal conductivity, mechanical properties of materials, anti erosion & abrasion resistance and engineering cost, the enamel heat exchange tube can solve the problem of low temperature corrosion. Enamel heat exchange tube has excellent performance of low temperature corrosion resistance, wear resistance and heat conduction, and the capability of heat transfer is superior to the steel pipe. It has been verified that the enamel heat exchange tube can satisfy the technical requirement, and has important engineering application by engineering practice.
Thermal-Hydraulic Calculation and Analysis on Evaporator System of a 1000 MW Ultra-Supercritical Pulverized Combustion Boiler with Double Reheat

Wan Li,Yang Dong,Zhou Xihong,Dong Le,Li Juan

DOI: https://doi.org/10.1007/s11630-020-1322-2

IF: 2.013

2020-01-01

Journal of Thermal Science

Abstract:A double reheat ultra-supercritical boiler is an important development direction for high-parameter and large-capacity coal-fired power plants due to its high thermal efficiency and environmental value. China has developed a 1000 MW double reheat ultra-supercritical boiler with steam parameters of 35 MPa at 605°C/613°C/613°C. Reasonable water wall design is one of the keys to safe and reliable operation of the boiler. In order to examine the thermal-hydraulic characteristics of the double reheat ultra-supercritical boiler, the water wall system was equivalent to a flow network comprising series-parallel circuits, linking circuits and pressure nodes, and a calculation model was built on account of the conservation equations of energy, momentum and mass. Through the iterative solving of nonlinear equations, the prediction parameters of the water wall at boiler maximum continue rate(BMCR), 75% turbine heat-acceptance rate(THA) and 30% THA loads, including total pressure drops, flow distribution, outlet steam temperatures, fluid and metal temperatures were gotten. The results of calculation exhibit excellent thermal-hydraulic characteristics and substantiate the feasibility of the water wall design of the double reheat ultra-supercritical boiler.
Experimental Study of Intermediate Header Flow Distribution Characteristics of a Supercritical Once-through Boiler Operating at Variable Pressures

朱玉琴,毕勤成,陈听宽

2009-01-01

Abstract:In the light of the structural and parameter features of an intermediate header serving as a transition connection between the spiral coil-tube water-wall at the lower part of the furnace and the vertical tube water-wall at the upper part of the fur-nace in a 600 MW supercritical boiler,the distribution characteristics of gas-liquid two-phase flows in the intermediate header of the supercritical boiler at a load of 35% ECR (Economical Continuous Rating) ,50% ECR and 75% ECR were simulated by using an air-water test loop.Through observations and a high-speed photographic method,the flow pattern in parallel branch tubes of a distribution header was measured and analyzed. By using a quick-closing valve and friction re-sistance method,measured respectively were the phase and flow distribution among various branch tubes. The test results show that at three operating conditions and with inlet dryness ranging from x = 0.7 to 0.95,the flow distribution of the air-water two-phase flows passing through the parallel branch tubes of the distribution header is comparatively uniform,and in most cases,the flow rate deviation is less than 10%.
Computational analysis on hydrodynamic characteristics and flow instability of an ultra supercritical 1000 MW double-reheat unit boiler

Kaiyuan MAO,Xin NIE,Haiyan XIE,Dong YANG,Fengjun WANG,Ying HUANG

DOI: https://doi.org/10.3969/j.issn.1002-3364.2017.08.036

2017-01-01

Abstract:The ultra supercritical 1000 MW unit boiler with double-reheat cycle in Datang Leizhou Power Plant adoptsП type arrangement. Due to the complexity of water flow inП type boiler, there exists the risk of uneven distribution of mass flow rate, which may result in the water wall overheat accident. In the processes of unit wide load operation and fast peak shaving, flow instability may occur in the water wall of the boiler due to the coal supply disturbance. To solve these problems, the distributions of mass flow rate, working fluid and metal temperatures in water wall at BMCR load were calculated by flow network system method, and the flow instability was checked for 30％THA load. On this basis, the optimal design and safe operation of the water wall were analyzed. The calculation results show that the water wall can avoid excessive stress between pipes and tension crack. The mass flow rate can finally restore stability after being disturbed by heat load. The water wall is safe and reliable.
The Fabrication and Inspection of the Ultra-Supercritical Separator

Biao Zhu

2009-01-01

Abstract:Being that the higher-grade material and the special structure of the separator which is partial of 1 000 MW Ultra-Supercritical boiler,the orientation dimension of the inclined nozzle assembled on the separator and the welding of the higher-grade material is the difficulty for quality control.This paper has introduced the new quality control technology of the separator during shop fabrication,especially in the process of material,welding,assembly and heat treatment.Detailed explain the new measuring technique that application in the assemblage of the separator.
REASONABLY WORKING OUT SOOTBLOWING SCHEME OF UTILITY BOILERS

杨卫娟,周俊虎,刘建忠,周志军,曹欣玉,岑可法

DOI: https://doi.org/10.3969/j.issn.1002-3364.2002.04.004

2002-01-01

Abstract:The reasonable heat-absorbing distribution share of boiler's heating surface among superheater, reheater and evaporator has been analyzed, the influence of boiler's heating surface contamination upon heat-tramsfer of other heating surfaces having been calculated. According to the principle of min energy consumption, how to calculate the optimal sootblowing cycle of individual heat surface is demonstrated, the method and steps of reasonably determining the sootblowing scheme and the method of keeping steam parameters in the sootblowing process are given, providing with valuable reference for sootblowing operation of utility boilers.
Design and Operation of Experimental System for Studying Heat Transfer in a Smooth Tube at Near and Super Critical Pressure

Li Wenkai,Wu Yuxin,Li Yan,Lu Junfu,Zhang Hai

DOI: https://doi.org/10.1007/978-3-642-02682-9_52

2009-01-01

Abstract:Boilers running at supercritical pressure with large capacity have been widely used in power generation technology. How to keep the safety of heat transfer in the riser system is an important issue. However, it is difficult to study heat transfer for the vertical smooth tubes in a boiler at sub-critical or supercritical pressure since the thermodynamic properties of water is very complex and sensitive to temperature and pressure near the critical point. Hot-state experiment of heat transfer for the tubes of diameter used in a boiler is of great value for the design of membrane wall. In order to study the heat transfer of vertical smooth tubes running at low heat flux and low mass flux for sub-critical CFB boilers, a near-supercritical pressure water test bed was built in Tsinghua University. The designed pressure is 21MPa, the mass flux of water is 550kg/m2s, and the heat flux is 136kW/m. In this paper, the design and structure of the test bed is introduced. The experimental result is analyzed, more experimental work is needed in future research.
Experimental and Theoretical Analysis on the Safety and Efficiency of an Ultra-Supercritical Pulverized Coal-Fired Boiler with Low Mass Flux Vertical Water Wall

Siyang Wang,Dong Yang,Dan Liu,Shijie Ouyang,Wenyu Wang

DOI: https://doi.org/10.1016/j.applthermaleng.2018.10.015

IF: 6.4

2019-01-01

Applied Thermal Engineering

Abstract:The heat transfer safety of low mass flux vertical water wall suitable for a high efficiency and wide-load ultra-supercritical coal-fired boiler is investigated experimentally. The pressure drop characteristics of supercritical water are discussed. The net thermal efficiency of an ultra-supercritical pulverized coal-fired power plant is analyzed theoretically by considering the power consumption of the feed water pump. The experimental results demonstrate the test water wall tube exhibits good heat transfer and low pressure drop characteristics at low mass flux and in the normal heat flux range. However, the self-compensation characteristic between parallel tubes can be destroyed at high test heat flux when the test pressure is near the critical value. In this case, the metal temperature and pressure drop of the water wall tube increase fast and abnormally. This phenomenon indicates the distributions of in-tube mass flux and furnace heat flux no longer match, which threatens the heat transfer safety of the water wall. Corresponding analysis demonstrates that on the premise of ensuring the heat transfer safety of the water wall, adopting the low mass flux technology can improve net thermal efficiency of the power plant.
An Experimental Study on Distribution Characteristics of High Pressure Steam-Water Two-Phase Flow

Yuqin Zhu,Weishu Wang,Qincheng Bi

DOI: https://doi.org/10.1166/asl.2011.1495

2011-01-01

Advanced Science Letters

Abstract:Supercritical pressure once-through boiler for sliding pressure operation is the most advanced thermal power unit in the world today and represents the trends of China's development of the thermal power construction. When the boiler is running at lower power loads or during start-up, after leaving middle distribution headers of the transitional water walls, the mixture of steam-water will redistribute in the vertical water wall tubes. If a large flow deviation in the vertical water wall tubes and a large steam temperature deviation at the exit of vertical water wall tubes occur, they will affect the boiler's safety. To develop 600 MW supercritical pressure once-through boilers with sliding pressure operation, in this paper, a systematic experiment had been performed to study the distribution characteristics of two-phase flow in the middle distribution header and vertical water wall tubes at a high pressure steam-water test loop for the first time. The condition of the test parameter is as follows: the pressure p = 10 similar to 21 MPa, the mass velocity in inlet tube of distribution header G = 400 similar to 1200 kg/(m(2) . s), and the inlet steam quality x = 0.7 similar to 1.0. The research results not only have significant engineering meaning to ensure the boilers working safely and operating at high efficiency, but also will provide design basis for the supercritical pressure boilers with intellectual property rights in China.
Welding techniques and its application in thermal power plant

Xueqin Lü,Gang Liu,Xiaoxia Zheng,Yixiong Wu

2009-01-01

Abstract:Presently ultra-supercritical pressure thermal power unit adopt some new materials and methods. This paper mainly briefs the welding performances, constituent of the welding joint, mechanical and its non-destructive inspection of automatic welding defects. Such as the essences of welding technique and processes in ultra super-critical unit main steam pipe, which uses SA335P92 and SA335P122 steel. The schemes and improvement measures for construction site heat treatment device configuration and technology selection are introduced.
ICOPE-15-C004 Thermal-hydraulic Analysis and Metal Temperature Computation for the Water Wall of a 1000MW Ultra Supercritical Tower Boiler with Double Reheat

Dong Yang,Long Wang,Yanshuang Bi,Beibei Xie,Gang Wang,Danhua Yao

DOI: https://doi.org/10.1299/jsmeicope.2015.12._icope-15-_121

2015-01-01

The Proceedings of the International Conference on Power Engineering (ICOPE)

Abstract:The ultra supercritical boiler technology with double reheat can significantly increase the efficiency of a Rankine cycle power plant, and reduce fuel consumption for a given output. Recently China is developing 1000MW ultra supercritical boiler with double reheat which is arranged in tower type and the steam parameters are 350bar, 605℃/613℃/613℃. Thermal-hydraulic analysis is the key factors for the design and operation of ultra supercritical boiler with double reheat. According to the boiler structure and furnace-sided heat flux, the water wall of an ultra supercritical tower boiler with double reheat is treated in this paper as a flow network system consisting of series-parallel loops, pressure grids and connecting tubes. Based on the mass, momentum and energy conservations and some supplementary equations, a mathematical model is developed. Pressure drop, mass flux distribution, outlet vapor temperatures and metal temperatures data in the water wall at BMCR (boiler maximum continuous rating), 75% THA (turbine heat acceptance) and 30% THA load are obtained by iteratively solving the mathematical model. The results show that the water wall in the ultra supercritical boiler can operate safely.
Hydrodynamic Characteristics of Vertical Tubes With Low Mass Flux in Supercritical Pulverized Coal Boiler

ZHANG Dalong,WU Yuxin,ZHANG Hai,LU Junfu,LIU Qing

DOI: https://doi.org/10.13334/j.0258-8013.pcsee.2014.32.001

2014-01-01

Abstract:In order to study the hydrodynamic characteristics of vertical tube designed boilers with low mass flux under supercritical conditions, the heat transfer model and the hydrodynamic model of water in a supercritical boiler water wall were established. Calculations for the hydrodynamics of a 600 MW supercritical boiler with low mass flux and vertical tubes were conducted. Under different boiler loads, the results of fluid flow, heat transfer and pressure drop of water in vertical smooth tubes and in ribbed tubes were analyzed. The advantages and disadvantages of such two layout schemes were shown. Based on the analysis, two retrofit methods, installing the throttle ring and arranging middle mixing-header, were considered for the smooth tube designed boilers. The hydrodynamic calculation results under these two retrofit methods show that heat transfer and flow conditions in the boiler wall are improved. The final optimization design of the boiler wall was provided, which would be a reference for the boiler design.
Analysis and Solution of High-temperature Corrosion for a 1000 MW Ultra-supercritical Boiler

Hongkun Lü,Jialin TONG,Jianzhong LIU,Ming ZHANG,Jianguo XIONG,Zhijun ZHOU

DOI: https://doi.org/10.11936/bjutxb2016070021

2017-01-01

Abstract:In order to control the high-temperature corrosion of water-wall, the pinning atmosphere was measured and the flake pieces were analyzed by SEM, EDS and XRD. The results show that the main reasons of water-wall high-temperature corrosion are cycle-by-cycle variation of reductive atmosphere. The area of most intense of reductive atmosphere and the concentration of H2 S is between OFA and SOFA. The possibility of the high-temperature corrosion of this area is great. Dual tangential circle wall firing can raise the concentration of H2 S at front-wall and back-wall. The outside corrosion product is Fe2 O3 , and on the contrary, the inside one is FeS. The alternation of the pinning atmospheres from oxidation atmosphere to reductive atmosphere which caused by load was a key factor of the high-temperature corrosion. In actual operation of boiler, optimizing air distribution mode and keeping the pinning atmosphere stabilization can reduce the rate of the high-temperature corrosion to low NOx combustion boilers.
Hydrodynamic characteristics of vertical water-wall in ultra-supercritical pressure boiler

WANG Weishu,ZHAO Pengfei,CHEN Gang,BI Qincheng,GU Hongfang

DOI: https://doi.org/10.3969/j.issn.0438-1157.2013.09.019

2013-01-01

Abstract:In view of the hydrodynamic characteristics of water-wall in ultra-supercritical pressure boiler,a hydrodynamic model was established for complicated series-parallel circuit system.The hydrodynamic calculation procedure was developed based on the POWERSTATION4.0 platform.According to the principle of equal exit temperature of working fluid,the throttle orifice plate compensating pressure drop was numerically calculated.The verifying calculation for mass flow distribution and pressure drop characteristics was carried out at a given heat load and designed throttle orifice plate.The hydrodynamic characteristic curve was drawn by Chebyshev polynomial fitting method.The vertical water-wall hydrodynamic characteristics of 1000 MW ultra-supercritical pressure boilers were also investigated numerically.The results show that U-type bifurcate tubes are good for the throttle orifice adjustment of vertical water-wall.The lower furnace of boiler has strong positive flow characteristics at low load rate but weak negative flow characteristics in supercritical load.The upper furnace of boiler has negative flow characteristics at different load rates.The curve of water-wall hydrodynamic characteristics increases monotonically,which means that the pressure drop of water-wall only depends on the mass flow.These results provide reliable theoretical basis for engineering design and operational monitoring of ultra-supercritical pressure concurrent boiler vertical water-walls.
Materials for ultra-supercritical coal-fired power plant boilers

R. Viswanathan,K. Coleman,U. Rao

DOI: https://doi.org/10.1016/j.ijpvp.2006.08.006

IF: 2.56

2006-11-01

International Journal of Pressure Vessels and Piping

Abstract:The efficiency of conventional fossil power plants is a strong function of the steam temperature and pressure. Research to increase both has been pursued worldwide, since the energy crisis in the 1970s. The need to reduce CO2 emission has recently provided an additional incentive to increase efficiency. The main enabling technology in achieving the above goals has been the development of stronger high-temperature materials. Extensive R&D programs have resulted in numerous high strength alloys for heavy section piping, and tubing needed to build boilers. The study reported here is aimed at identifying, evaluating and qualifying the materials needed for the construction of the critical components of coal-fired boilers capable of operating with 760°C (1400°F)/35MPa (5000psi) steam. The economic viability of such a plant has been explored. Candidate alloys applicable to various ranges of temperature have been identified. Stress rupture tests have been completed on the base metal and on welds to a number of alloys. Steamside oxidation tests in an autoclave at 650 (1200°F) and 800°C (1475°F) have been completed. Fireside corrosion tests have been conducted under conditions simulating those of waterwalls and superheater/reheater tubes. Weldability and fabricability of the alloys have been investigated. The capability of various overlay coatings and diffusion coatings have been examined. This paper provides a status report on the progress achieved to date on this project.

engineering, mechanical, multidisciplinary
Thermal–Hydraulic Calculation and Analysis on Water Wall System of a 700 MWe Ultra-Supercritical CFB Boiler

Haowen Wu,Tuo Zhou,Xiannan Hu,Yongjun Luo,Man Zhang,Hairui Yang

DOI: https://doi.org/10.3390/en16114344

IF: 3.2

2023-01-01

Energies

Abstract:Ultra-supercritical circulating fluidized bed (CFB) boiler combustion technology has the advantages of environmental protection and good commercialization. As one of the key aspects in ultra-supercritical CFB combustion technology, the water wall system directly determines whether the CFB boiler can safely and effectively transform heat energy. This paper studies the thermal–hydraulic characteristics of the designed water wall system of a 700 MWe ultra-supercritical CFB boiler, the largest one that will be built next year. At four loads of the water wall system, hydrodynamic parameters are calculated based on the successfully verified mathematical models. The results show that the hydrodynamic characteristics of the system are good. The temperature distribution of the working fluid and metal of the water wall system is acceptable and safe at each load, which can support the technical development and improvement of the 700 MWe ultra-supercritical CFB boiler.

Introduction to Ultra-Supercritical Boiler Blowpipe Program

Technical Study on Three-Staged Pipe-Blowing Method Used in Double Reheat Unit

Practice and optimization of combined pipe-blowing method for domestic first double-reheat unit

Automatic Welding System Design for Connecting Piece of Heating Surface Piping of Ultra Supercritical Boiler

Analysis on the Steam Temperature Deviation of the Vertical Water Wall and the Adjustment Plan of the Throttle Ring for an Ultra-supercritical Boiler

Application study on enamel heat exchange tube in GGH of coal-fired units with ultra-low flue gas emission

Thermal-Hydraulic Calculation and Analysis on Evaporator System of a 1000 MW Ultra-Supercritical Pulverized Combustion Boiler with Double Reheat

Experimental Study of Intermediate Header Flow Distribution Characteristics of a Supercritical Once-through Boiler Operating at Variable Pressures

Computational analysis on hydrodynamic characteristics and flow instability of an ultra supercritical 1000 MW double-reheat unit boiler

The Fabrication and Inspection of the Ultra-Supercritical Separator

REASONABLY WORKING OUT SOOTBLOWING SCHEME OF UTILITY BOILERS

Design and Operation of Experimental System for Studying Heat Transfer in a Smooth Tube at Near and Super Critical Pressure

Experimental and Theoretical Analysis on the Safety and Efficiency of an Ultra-Supercritical Pulverized Coal-Fired Boiler with Low Mass Flux Vertical Water Wall

An Experimental Study on Distribution Characteristics of High Pressure Steam-Water Two-Phase Flow

Welding techniques and its application in thermal power plant

ICOPE-15-C004 Thermal-hydraulic Analysis and Metal Temperature Computation for the Water Wall of a 1000MW Ultra Supercritical Tower Boiler with Double Reheat

Hydrodynamic Characteristics of Vertical Tubes With Low Mass Flux in Supercritical Pulverized Coal Boiler

Analysis and Solution of High-temperature Corrosion for a 1000 MW Ultra-supercritical Boiler

Hydrodynamic characteristics of vertical water-wall in ultra-supercritical pressure boiler

Materials for ultra-supercritical coal-fired power plant boilers

Thermal–Hydraulic Calculation and Analysis on Water Wall System of a 700 MWe Ultra-Supercritical CFB Boiler