Abstract:Nanosized copper oxide-zirconia particles containing 10-30 mol% of copper were prepared by using a precipitation technique in aqueous tetramethylammonium hydroxide solutions. Two methods, in situ (INS) and step-by-step (SBS), which differed in the time when the copper salt was introduced to the synthesis procedure, were used, and this allowed a comparison of the properties of the final powders produced using the two modes of preparation. The surface areas and phase compositions were different for the samples prepared from the two different methods after calcination at 500 degreesC. A surface area of 168 m(2) g(-1) was obtained for the sample prepared with the SBS method and 121 m(2) g(-1) for the INS method, both contain 30 mol% copper. Tetragonal ZrO2 was observed from X-ray diffraction patterns for all samples prepared with the SBS method, however, no separate phase of copper or copper oxide was observed. It is proposed that all of the copper is finely distributed on the surface of the ZrO2 particles with the SBS method. For the samples prepared from the INS method, tetragonal ZrO2 was obtained at a low copper content and the peaks indexed to tetragonal ZrO2 shifted to higher angle with the increase of copper content, indicating copper ions being incorporated into the lattice. An amorphous compound was obtained at high copper content (30 mol%). The phase change with the calcination temperature was also investigated for the INS sample containing 30 mol% copper. The studies show that tetragonal ZrO2 and copper oxide were present after calcination at 400 degreesC, and tetragonal ZrO2 with a small amount of monoclinic ZrO2, as well as copper oxide, formed after calcination at 700 degreesC. However, after heating at 500 degreesC, amorphous compounds were obtained, suggesting that 500 degreesC could be a phase transition point. The incorporation of copper in the ZrO2 lattice resulted in a loss of order in the ZrO2 structure when calcined at 500 degreesC, with a further increase in the calcination temperature leading to the phase change.

Preparation of Cu Coated ZrW<sub>2</sub>O<sub>8</sub> Composite Powders Via Heterogeneous Precipitation Process

Preparation of Cu-ZrW2O8 Composite Coatings by Electric Deposition

Thermal properties and phase transitions of Cu-coated ZrW<sub>2</sub>O<sub>8</sub> composite powders

Thermal properties and phase transitions of Cu-coated ZrW 2O 8 composite powders

Synthesis of ZrW2O8–ZrC composite powders by solid‐state exothermic oxidation reaction of ZrC and WO3 powders

Preparation and Characterization of WC/Co-W-C Cermet Coatings with Molten Zinc Corrosion Resistance by HVOF Spraying of Bimodal-Structured WC/Co Powder

Preparation of Ultrafine Powder of ZrO2-Coated Si3N4 Composites

Preparation of Wcu Composite Powders by Sol-Gel Method and Their Reduction Behavior

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Synthesis of PbZrO3 Powder by a COprecipitation Method

PREPARATION OF ULTRAFINE W–Cu COMPOSITE POWDER USING ULTRASONIC-ASSISTED ELECTROLESS PLATING

Oxidation Resistance Improvement of ZrB2 Powders by the Deposition of Al2O3/Y2O3/ZrO2 Coatings Via Chemical Co-Precipitation Method

Preparation and characterization of CuO–ZrO2 nanopowders

Preparation and Microstructures of CoAl(2)O(4) ZrO(2) Composite

Preparation and characterization of nano-scale Y2O3-ZrO2 powder by heterogeneous precipitation

Ultra-coarse Cemented Tungsten Carbide with (zr,w)cx Precipitates in Ceramic Phase

Effect of Co on morphology and preparation of in situ synthesis of WC-Co composite powders

Precipitations of W/Cu metallic phases in ZrC in the reactive melt infiltrated ZrC/W composite

A Low Temperature Co-Precipitation Preparation of Nano-Sized Zinc Containing Β-Tricalcium Phosphate Powders

Particle Size and Purity Control Study on ZrW2O8 Powders Using Coprecipitation Method

Research on preparation process for the in situ nanosized Zr(Y)O2 particles dispersion-strengthened tungsten alloy through synthesizing doped hexagonal (NH4)0.33·WO3

Preparation of Cu Coated ZrW&lt;sub&gt;2&lt;/sub&gt;O&lt;sub&gt;8&lt;/sub&gt; Composite Powders Via Heterogeneous Precipitation Process