Abstract:Abstract Low‐noise and low‐voltage operation is prime requirement of an operational transconductance amplifier for low frequency applications. However, achieving low‐noise operation at low supply voltages is a challenging task in CMOS technology owing to noise‐power and noise‐stability tradeoffs. This article outlines, the design of four differential bias self‐cascode (DBSC) operational transconductance amplifiers (OTAs) working at ±0.7 V. The four design techniques namely gate driven (GD), bulk driven (BD), bulk driven quasi‐floating gate (BDQFG), and gate driven quasi floating bulk (GDQFB) have been applied on DBSC OTAs. The designing aspects and performance parameters of these four OTAs such as gain, gain‐bandwidth, input referred noise ( IRN ), settling time (ST), common mode rejection ratio (CMRR), total harmonic distortion, input impedance, transconductance, power consumption, area consumption and process/mismatch variations have been fairly compared in this work. These DBSC OTAs have been designed and simulated using a standard 0.18‐μm 6M1P CMOS N‐well process. The results infer GD DBSC OTA shows high CMRR of 125.83 dB. While the BD DBSC OTA consumes very low power of 0.2 μW. The BDQFG DBSC OTA shows low 1% ST of 24.83 μS. The GDQFB DBSC OTA show high transconductance (2.35 mS), high gain (64.97 dB), and low IRN (0.40 μV/√Hz at 10 Hz). The theoretical predictions for these OTAs agree with the post‐layout simulations. The proposed OTAs can be used for designing various analog circuits such as programmable gain amplifiers, variable gain amplifiers, and transimpedance amplifiers for low‐frequency biomedical and health care applications.

A Wide Linear Range Ultra-low Transconductance Amplifier for Biomedical Sensor Applications

High gain, high speed OTA for S/H circuit in 14-b 100-MS/s Pipeline ADC

A High-pass Filter with On-chip Body Bias Technique for Neural Signals Processing

An Ultra-Low-Voltage Transconductance Stable and Enhanced OTA for ECG Signal Processing

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

A Programmable Low Power Current Source for Bioimpedance Measurement: Towards a Wearable Personalized Health Assistant.

Design of low power, programmable low-Gm OTAs and Gm-C filters for biomedical applications

0.5 V Multiple-Input Fully Differential Operational Transconductance Amplifier and Its Application to a Fifth-Order Chebyshev Low-Pass Filter for Bio-Signal Processing

Design of Low-Offset Low-Power CMOS Amplifier for Biosensor Application

Design of low‐voltage low‐noise operational transconductance amplifiers for low frequency applications

A 0.5-V 0.02% THD Bulk-Driven OTA for Continuous-Time Applications in 180 nm CMOS

A Linear CMOS OTA and Its Application to a 3. 3V 20MHz High-Q g m-C Bandpass Filter

Highly linear OTA with 3rd-order nonlinearity superposition techniques for Gm-C low-pass filter with 34dBm IIP3

Modeling and Designing of High-Gain, Wide-Band and Fast-Speed Operational Transconductance Amplifier

A High Linearity Large Time Constants Switched-Resistor Filter for Biomedical Applications

Design of a Low-Power High-Gain Bio-Medical Operational Amplifier in 65nm Technology using gm/ID Methodology

Design and Implementation of Ultralow Current-Mode Amplifier for Biosensor Applications

A 0.5-V Ultra-Low-Power Low-Pass Filter with a Bulk-Feedback Technique

0.5-V High Linear Fully Differential Multiple-Input Bulk-Driven OTA With Effective Self-Embedded CMFB

Design of a Low-Power/Low-Voltage Class-AB OTA

A Fully Differential Super Self-Biasing Operational Transconductance Amplifier