Abstract:Ultra-low-power circuits that can work under a low-voltage supply are in great demand in future wearable biomedical applications, which tend to be integrated with low-output-voltage energy harvesting devices. In this paper, we present a low-voltage low-power continuous-time low-pass filter (CT-LPF), which is indispensable in biomedical systems. When a low-voltage supply is used, it is necessary to make the output quiescent voltage (V-Q) stable in the LPF, otherwise the dynamic range will be reduced. Conventional Source-follower (SF) based topologies can achieve ultra-low-power consumption. However, the difference of the input and output V-Q is sensitive to process and temperature variations. In this work, a complementary SF based topology with a bulk-common-mode-feedback (B-CMFB) circuit is proposed to keep the output V-Q tracking the input V-Q and immune to the process and temperature variations. A 4th-order LPF using the proposed topology has been implemented in a standard 0.18 mu m CMOS process, which achieves a power consumption of only 3.69-nW under a 0.5-V voltage supply with a bandwidth of 200 Hz. Measurement results show that the input-referred noise is 91.9 mu V-rms. The IIP3 is 5.0 dBm and the dynamic range (DR) is 48.5 dB. The active chip area is only 0.074 mm(2). The proposed LPF achieves both ultra-low power consumption with a 0.5-V supply and a stable output V-Q immune to process and temperature variations, which is suitable for low-supply-voltage biomedical systems.

A 0.5-V Ultra-Low-Power Low-Pass Filter with a Bulk-Feedback Technique

A 0.5-V 3.69-nW Complementary Source-Follower-C Based Low-Pass Filter for Wearable Biomedical Applications

Low-dropout regulator with no off-chip capacitor and ultra low power consumption

0.28-nW level-shifter folded flipped source follower fourth-order low-pass-filter IC design

0.279 nW fourth-order filter circuit for biological signal conditioning

A 5th order 0.8/2.4 GHz programmable active band pass filter for power DAC applications

An Ultra-Low Power K band Balanced Frequency Doubler with a Novel Current-reused Structure

A 0.65mw 20mhz 5Th-Order Low-Pass Filter With+28.8dbm Iip3 Using Source Follower Coupling

A 77-dB-DR 0.65-mW 20-MHz 5th-Order Coupled Source Followers Based Low-Pass Filter

A Chopper-Stabilized Source Follower Coupling Based Low-Pass Filter with Noise Reduction

A 0.6mw 31mhz 4Th-Order Low-Pass Filter with +29dbm IIP3 Using Self-Coupled Source Follower Based Biquads in 0.18µm CMOS

A 0.6-V Power-Efficient Active-RC Analog Low-Pass Filter With Cutoff Frequency Selection

A Highly Linear 0.9V 3Rd-Order Acitve-RC Low-Pass Filter in CMOS 28Nm

A Wideband Inductorless LNA with Local Feedback and Noise Cancelling for Low-Power Low-Voltage Applications

A Low Noise High PSR LDO Based on N-type Flipped Voltage Follower

A 20–80 MHz Continuously Tunable Gm-C Low-Pass Filter for Ultra-Low Power WBAN Receiver Front-End

A CMOS Programmable Fourth-Order Butterworth Active-RC Low-Pass Filter

Analysis and Design of Ultra-Wideband Low-Noise Amplifier with Input/Output Bandwidth Optimization and Single-Ended/Differential-Input Reconfigurability.

A Wide Linear Range Ultra-low Transconductance Amplifier for Biomedical Sensor Applications

A 2.3mA 240-to-500MHz 6th-order active-RC low-pass filter for ultra-wideband transceiver

A CMOS 0.5&#x2013;10.6 GHz Inductor Feedback Low Noise Amplifier for Multi-Standard Application