Abstract:Recent advances in electronics and microelectronics have aided the development of low-cost devices that are widely used as well-being or preventive monitoring devices by many people. Remote health monitoring, which includes wearable sensors, actuators, and modern communication and information systems, offers effective programs that allow people to live peacefully in their own homes while also being protected in some way. High-frequency noise, power-line interface, and baseline drift are prevalent during the data-acquisition system of an ECG signal, and they can limit signal understanding. They (noises) must be isolated in order to provide an appropriate diagnostic of the patient. When removing high-frequency components (noise) from an ECG signal with an FIR filter, the critical path delay increases considerably as the filter's duration increases. To reduce high-frequency noise, simple moving average filters with pipelining and look-ahead transformation techniques are extensively used in this study. With the use of pipelining and look-ahead techniques, the only objective is to increase the clock speed of the designs. The moving average filters (conventional and proposed) were created on an Altera Cyclone IV FPGA EP4CE115F29C7 chip using the Quartus II software v13.1 tool. Finally, performance metrics such logic elements, clock speed, and power consumption were compared and studied thoroughly. The recursive pipelined 8-tap MA filter with look-ahead approach outperforms the other designs (685.48 MHz) in this investigation.

0.28-nW level-shifter folded flipped source follower fourth-order low-pass-filter IC design

0.279 nW fourth-order filter circuit for biological signal conditioning

A 0.5-V 3.69-nW Complementary Source-Follower-C Based Low-Pass Filter for Wearable Biomedical Applications

A 0.5-V Ultra-Low-Power Low-Pass Filter with a Bulk-Feedback Technique

A 5th order 0.8/2.4 GHz programmable active band pass filter for power DAC applications

A 0.6V 32.5mw Highly Integrated Receiver for 2.4ghz ISM-Band Applications

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

20 . 6 A 0 . 6 V 32 . 5 mW Highly Integrated Receiver for 2 . 4 GHz ISM-Band Applications

A 77-dB-DR 0.65-mW 20-MHz 5th-Order Coupled Source Followers Based Low-Pass Filter

Low power design for 14-bit 100MSPS pipelined ADC

A 0.65mw 20mhz 5Th-Order Low-Pass Filter With+28.8dbm Iip3 Using Source Follower Coupling

A 0.6mw 31mhz 4Th-Order Low-Pass Filter with +29dbm IIP3 Using Self-Coupled Source Follower Based Biquads in 0.18µm CMOS

A Highly Linear 0.9V 3Rd-Order Acitve-RC Low-Pass Filter in CMOS 28Nm

A Low Noise High PSR LDO Based on N-type Flipped Voltage Follower

A novel low-complexity digital filter design for wearable ECG devices

Reconfigurable Architectures with High-Frequency Noise Suppression for Wearable ECG Devices

A New 22 nm ULPLS Architecture to Detect 70 mV Minimum Input, Suitable for IOT Applications

A Low Power Programmable Band-Pass Filter with Novel Pseudo-Resistor for Portable Biopotential Acquisition System.

A Chopper-Stabilized Source Follower Coupling Based Low-Pass Filter with Noise Reduction

A layout strategy for low-power voltage level shifters in 28nm UTBB FDSOI technology

A Fifth-Order 20-Mhz Transistorized-Lc-Ladder Lpf With 58.2-Db Sfdr, 68-Mu W/Pole/Mhz Efficiency, And 0.13-Mm(2) Die Size In 90-Nm Cmos