Abstract:Abstract Background: Recording of electrical activity of neurons is indispensable for decoding the information in the brain. The amplitude of signals recorded by electrodes is small, and it must be amplified to the level that can be digitalized by the analog-to-digital convert (ADC). A micro-power low-noise neural recording amplifier is indispensable for implant hippocampal cognitive prosthesis. When the process turns into deep submicron, the gate leakage current of the metal oxide semiconductor (MOS) transistor becomes larger and mismatch between devices becomes worsen. It is necessary to keep the neural amplifier robust in all process corners. Methods: The proposed circuit is a two-stage amplifier which can achieve a good trade-off between power consumption and noise. Four second-stage amplifiers share a common reference amplifier to reduce area and power consumption. A pseudo-resistor with high resistance is utilized to realize a very-low frequency high pass corner without external components. In order to minimize process variation, a bulk-compensated (BC) technique is adopted to maintain adequate tolerance in all corner case. Results: The 4-channel neural amplifier is designed and fabricated in a 40 nm standard complementary metal oxide semiconductor (CMOS) process. It achieves a mid-band gain of 54 dB, a bandwidth of 70 Hz to 7.7 kHz, a total input-referred noise of 3.2 μVrms , and a Noise Efficiency Factor (NEF) of 3.3 while consuming 4.68 µW from the 1.1 V supply. The core area of one channel is only 0.032 mm 2 . Conclusion: A 4-channel integrated neural recording amplifier chip with bias-compensated circuits is presented in this paper. Extensive simulations insure that the design is “center”. The chip layout is verified using design rules check (DRC) and layout versus schematic (LVS) design check with the help of verification tools. Test results shows that it is less sensitive to process variation and consumes less power compared with amplifier without bulk-compensated circuit. This makes the design robust and uniquely appropriate for low-power implant application.

A High-pass Filter with On-chip Body Bias Technique for Neural Signals Processing

A receiver analog front-end for body sensor network

The Design of Broadband LNA with Active Biasing Based on Negative Technique

A 40 Nm Cmos V-Band Vco with On-Chip Body Bias Voltage Control Technique

A BiCMOS Implementation of Noise Canceling Low Noise Amplifier for Wideband Applications

A Wideband BiCMOS Thermal Noise Canceling Low Noise Amplifier with Temperature Compensation

A Robust 4-channel Micro-power Low-noise Neural Recording Amplifier for Hippocampal Cognitive Prosthesis

A 5th order 0.8/2.4 GHz programmable active band pass filter for power DAC applications

The Design Of High-Frequency Ota-C Filter For Wireless Sensors Network Applications

Design of Readout Circuit Based on Probe Neural Biosensor

A Wide Linear Range Ultra-low Transconductance Amplifier for Biomedical Sensor Applications

Novel design of a low power neural amplifier using split push pull balanced high swing OTA for brain machine interface

Design Considerations and Implementation for Low Power Transconductance-Capacitance Filter with On-Chip Automatic Tuning

Optimised Design and Implementation of Band-Pass Filter for Neural Recording System

A Low Power OTA-C Filter for Wireless Body Area Networks

A High Q Gm-C Filter with On-Chip Automatic Tuning Circuit Implemented in Nano-Scale CMOS Process

A New Low-Power Non-uniform Sample and Hold Circuit for Biomedical Signal Processing Applications

A Low Power Programmable Band-Pass Filter with Novel Pseudo-Resistor for Portable Biopotential Acquisition System.

A Novel CMOS High Accuracy Fast Speed OTA for Switched-Capacitor Filters

A highly efficient adaptive body bias CMOS rectifier with double-side feedback at a tone of 2.4 GHz

0.5 V Multiple-Input Fully Differential Operational Transconductance Amplifier and Its Application to a Fifth-Order Chebyshev Low-Pass Filter for Bio-Signal Processing