Abstract:The scope of this work is to provide an overview of the influences of process parameters, print orientation, and post-process treatments of Ti6AlV4 processed by laser powder bed fusion on its microstructure and physical and mechanical properties and their anisotropic behavior. To avoid the influence of changes in powder quality and ensure comparability, experiments were carried out using a single batch of virgin powder. First, characterization of the density and surface roughness was performed to optimize the process parameters utilizing design of experiment. Tensile, notched bar impact and compression test specimens were built in three different orientations: vertically, horizontally, and inclined at 45° to the build plate. Later, the influence of the staircase effect and the possible course of anisotropy from vertical to horizontal were investigated. Subsequently, heat treatments for stress relief, furnace annealing, and hot isostatic pressing were performed. In addition to as-built samples, mechanical machining and a two-step electrochemical polishing surface treatment were applied to investigate the influence of the surface roughness. With parameter optimization, a relative density of 99.8% was achieved, and surface roughness was improved over default parameters, reducing Ra by up to 7 μm. Electrochemical polishing is a viable way to decrease the surface roughness. An Ra value of 1 μm and an Rz value of 4 μm can be achieved for 45° downskin surfaces with as-built surface roughness values of Ra 24 μm and Rz 117 μm. As-built and stress-relieved conditions show little anisotropy in their yield and tensile strength (max 2.7%), but there is a strong influence of the build orientation on necking, and brittle fracture behavior is shown due to the martensitic microstructure (up to 70%). Heat treatment can increase the ductility and further decrease the strength anisotropy with both furnace annealing and hot isostatic pressing delivering similar results for tensile properties, while angled samples exhibit behavior that is closer to vertical than horizontal, indicating a non-linear change in break behavior. Electrochemical polishing increases fracture necking, and its isotropy drastically increases from 4% to over 30% compared with as-built parts, which is close to the level of the machined specimen.

Mechanical Properties Anisotropy of Ti−6Al−4V Alloy Fabricated by Β Forging

The anisotropy of fracture toughness of an α+β titanium alloy by β forging

On the texture and mechanical property anisotropy of Ti6Al4V alloy fabricated by powder-bed based laser additive manufacturing

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Anisotropic microstructure and mechanical properties of as-forged (Ti, Nb)B/Ti2AlNb composites

Anisotropy of Rotating Bending Fatigue Properties of Α Plus SS Titanium Alloy

Mechanical and Physical Characterizations of a Three-Phase TiAl Alloy during Near Isothermal Forging

Multiple Α Sub-Variants and Anisotropic Mechanical Properties of an Additively-Manufactured Ti-6Al-4V Alloy

Effects of the crystallographic and spatial orientation of α lamellae on the anisotropic in-situ tensile behaviors of additive manufactured Ti–6Al–4V

Forging–microstructure–tensile properties correlation in a new near β high-strength titanium alloy

Research on tensile anisotropy of Ti-22Al-25Nb alloy isothermally forged in B2 phase region related with texture and variant selection

Anisotropic fatigue strength and status of crack initiation of Ti17 disk fabricated by through-transus-processed forging

The Effect of the Forging Process on the Microstructure and Mechanical Properties of a New Low-Cost Ti-5Al-1.5Mo-1.8Fe Alloy

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion

Microstructural stability, phase evolution and mechanical properties of a forged W-modified high-Mn β-γ-TiAl alloy

Achieving high strength-ductility synergy in a hierarchical structured metastable β-titanium alloy using through-transus forging

Influences of Surface, Heat Treatment, and Print Orientation on the Anisotropy of the Mechanical Properties and the Impact Strength of Ti 6Al 4V Processed by Laser Powder Bed Fusion

Microstructures and mechanical properties during sinter-forging of a novel TiAl alloy

Evolution of microstructure and texture of a near α titanium alloy during forging bar into disk

Rheology of Ti-6Al-4V alloy under non equilibrium conditions during β forging