Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

Research on tensile anisotropy of Ti-22Al-25Nb alloy isothermally forged in B2 phase region related with texture and variant selection

Anisotropy in Fracture Toughness and Toughening Mechanism of Ti-22Al-25Nb Alloy Related to Texture and Grain Boundary Damage

Anisotropic microstructure and mechanical properties of as-forged (Ti, Nb)B/Ti2AlNb composites

Tensile behavior and deformation mechanism for Ti–22Al–25Nb alloy with lamellar O microstructures

Plastic Deformation Mechanism and Interaction of B2, Α2, and O Phases in Ti22Al25Nb Alloy at Room Temperature

Mechanical Properties Anisotropy of Ti−6Al−4V Alloy Fabricated by Β Forging

Effect of Solution Treatment on Microstructure, Texture, and Anisotropy of Mechanical Properties in TA10 (Ti-0.3Mo-0.8Ni) Sheet

Anisotropy of Rotating Bending Fatigue Properties of Α Plus SS Titanium Alloy

Investigation of the O phase in the Ti–22Al–25Nb alloy during deformation at elevated temperatures: Plastic deformation mechanism and effect on B2 grain boundary embrittlement

Dependence of Mechanical Properties on the Microstructure Characteristics of a Near Β Titanium Alloy Ti-7333

Microstructure Evolution and Phase Transformations in Ti-22Al-25Nb Alloys Tailored by Super-Transus Solution Treatment

Textures of Rectangular Extrusions and Their Effects on the Mechanical Properties of Thermo-Mechanically Treated, Lamellar Microstructure, Ti–47Al–2Cr–2Nb–0.15B

Hot Tensile Behavior and Microstructure Evolution Mechanism of Ti2AlNb Sheet

Effects of Forging Deformation on Variant Selection and Morphology of Α in TiB/near Α-Ti Composites

Controllable Mechanical Anisotropy of Selective Laser Melted Ti6Al4V: A New Perspective into the Effect of Grain Orientations and Primary Grain Structure

Investigation on Anisotropic Mechanical Behavior of Ti-6Al-4V Alloy Via Schmid Factor and Kernel Average Misorientation Distribution

Microstructural and Mechanical Anisotropy of Extruded In-Situ TiB 2 /2024 Composite Plate

Effects of Plastic Deformation and Aging Treatment on Phase Precipitation in Ti2AlNb Alloy

The α 2 to orthorhombic O-phase transformation-facilitated high elastically mediated strain transfer ability in high Nb-TiAl alloys

O Phase Precipitation and Variant Selection in Ti–22Al–25Nb Alloy During the Hot Shear Spinning

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate